NextSDS Logo
Safety Data Sheet EN

Coolant VCS ready mixed mix 40/60

Scan your chemical compliance

Free 10-second scan. Upload a document and check compliance instantly.

Scan Now
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Coolant VCS ready mixed mix 40/60
Product Form
Liquid.
Product Code
22567314

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Coolant and antifreeze.

Uses advised against

Not applicable.

Manufacturers & Suppliers

A

AB Volvo Penta

SE-405 08 Gteborg Sweden

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4 H302
Repr. Cat. 1B H360D
STOT RE Cat. 2 H373

GHS Pictograms

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H302 harmful if swallowed.
H360D May damage the unborn child.
May cause damage to organs through prolonged or repeated exposure. (kidneys) (oral)

Precautionary Statements

If medical advice is needed, have product container or label in hand.
Keep out of reach of children.
Read label before use.
Wash thoroughly after handling.
Do not eat, drink or smoke when using this product.
IF SWALLOWED: Call a POISON CENTER or physician.
Rinse mouth.
Not applicable
Not applicable.

Manage your Safety Data Sheets

Organize and access chemical safety data with ease

Manage SDS
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment, are PBTs, vPvBs or Substances of equivalent concern, or have been assigned a workplace exposure limit and hence require reporting in this section.

Chemical Name CAS Number Concentration Hazardous
N/A --- 30 - 60% Yes
N/A --- 3% Yes
N/A --- 100% Yes

Occupational exposure limits, if available, are listed in Section 8.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, remove to fresh air. Get medical attention if symptoms occur.

Symptoms: May cause slight transient irritation.

Skin contact

Wash contaminated skin with soap and water. Get medical attention.

Symptoms: Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/or dermatitis.

Eye contact

In case of contact with eyes, rinse immediately with plenty of water. Get medical attention if symptoms occur. Continue to rinse for at least 10 minutes.

Symptoms: May cause slight transient irritation. ( redness )

Ingestion

Do not induce vomiting unless directed to do so by medical personnel. If affected person is conscious, give plenty of water to drink. Wash out mouth with water. (Coolant. Contains ethylene glycol) Get medical attention immediately.

Symptoms: Exposure can cause stomach pains, vomiting and diarrhoea.

Immediate Medical Attention

Get medical attention immediately (for ingestion).

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

The data for this section has not been processed yet.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

The data for this section has not been processed yet.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

The data for this section has not been processed yet.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Use only with adequate ventilation. If this product contains ingredients with exposure limits, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure below any recommended or statutory limits. Where reasonably practicable, this should be achieved by the use of local exhaust ventilation and good general extraction. If workers are exposed to concentrations above the exposure limit, they must use appropriate, certified respirators.

Hands

For prolonged or repeated handling, use gloves : nitrile rubber, butyl rubber, neoprene rubber. EN374

Eyes

Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts.

Respiratory

Provide adequate ventilation.

Skin/Body

Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Environmental

Do not allow to enter drains or watercourses.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Explosive Limits
---
Voc Content
---
Vapor Density
>1 [Air = 1]
Kinematic Viscosity
Not available.
Appearance
---
Physical State
Liquid.
Dynamic Viscosity
Not available.
Vapor Pressure
Not available.
Solubility
Easily soluble in cold water; Easily soluble in hot water
Density
1.056 g/cm3 [20 (68F)]
Relative Evaporation Rate
---
Metal Corrosion
---
Molecular Weight
---
Solidification Point
---
Colour
Yellow.
Lower Explosive Limit
Not available.
Cloud Point
---
Odor
Slight
Bulk Density
---
Upper Explosive Limit
Not available.
Freezing Point
Not available.
Partition Coefficient
Not applicable.
Physical State Data
liquid
Odor Threshold
Not available.
Form
---
Properties Status
---
Ph
8.6
Crystallisation Point
---
State Under Standard Conditions
---
Flammability
Not available.
Relative Density
Not available.
Softening Point
---
Evaporation Rate
---
Solubility In Water
Easily soluble
Flash Point
Not applicable.
Melting Point
Not available.
Auto Ignition Temperature
Not available.
Boiling Point
109 (228.2F)
Decomposition Temperature
Not available.
Colour Intensity
---
Solubility In Fat
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

The data for this section has not been processed yet.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
Not regulated.
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Coolant VCS ready mixed mix 40/60?

The signal word is danger.

What is the physical form of Coolant VCS ready mixed mix 40/60?

Coolant VCS ready mixed mix 40/60 is a liquid. with yellow. color. It has slight odor.

What is the solubility of Coolant VCS ready mixed mix 40/60?

Easily soluble in cold water; Easily soluble in hot water

What is Coolant VCS ready mixed mix 40/60 used for?

Coolant and antifreeze.

What are the hazard statements for Coolant VCS ready mixed mix 40/60?

This substance has 3 hazard statements:

  • H302: harmful if swallowed.
  • H360D: May damage the unborn child.
  • May cause damage to organs through prolonged or repeated exposure. (kidneys) (oral)

What is the melting point of Coolant VCS ready mixed mix 40/60?

The melting point is Not available. and the boiling point is 109 (228.2F).

Compliance Scanner

Scan your compliance