Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- CaFix seal
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen) PROC10 Roller application or brushing Waterproofing
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
CaPlast GmbH
manufacturer
Magdheide 7 59394 Nordkirchen
(+49) 25 99 / 91 3 - 0
www.caplast.de
Emergency Contacts
Giftinformationszentrum der Länder Rheinland-Pfalz und Hessen
+49 (0)6131 / 19 24 0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS08
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture: consisting of the following components.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| barium sulphate, natural EC: 231-784-4 | 7727-43-7 | 25 - 50% | Yes |
| Poly[oxy(methyl-1,2-ethanediyl)], alpha-hydro-omega-hydroxy-, polymer with 2,4-diisocyanato-1-methylbenzene EC: 609-378-7 | 37273-56-6 | 25 - 50% | Yes |
| Hydrocarbons, C9-C12, n-alkanes, isoalkanes, cyclics, aromatics(2-25%) EC: 919-446-0 | --- | 2.5 - 10% | Yes |
| xylene EC: 215-535-7 | 1330-20-7 | 2.5 - 10% | Yes |
| Kieselguhr, soda ash flux-calcined EC: 272-489-0 | 68855-54-9 | 2.5 - 10% | Yes |
| ethylbenzene EC: 202-849-4 | 100-41-4 | 0.5 - 2.5% | Yes |
| 4-isocyanatosulphonyltoluene EC: 223-810-8 | 4083-64-1 | 0.5 - 2.5% | Yes |
| hydrocarbons, C9, aromatic EC: 918-668-5 | --- | 0.5 - 2.5% | Yes |
| 2-ethylhexyl (6-isocyanatohexyl)-carbamate EC: 247-735-5 | 26488-60-8 | 0.5% | Yes |
| 4-methyl-m-phenylene diisocyanate EC: 209-544-5 | 584-84-9 | 0.5% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation. Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. Seek medical treatment.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. Protect unharmed eye.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, sand, extinguishing powder. Do not use water. ABC powder Alcohol resistant foam CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
Water with full jet
During heating or in case of fire poisonous gases are produced.
Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
Firefighter Protection
Do not inhale explosion gases or combustion gases.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unprotected persons away.
Do not allow product to reach sewage system or any water course. Inform respective authorities in case of seepage into water course or sewage system. Do not allow to enter sewers/ surface or ground water. Prevent from spreading (e.g. by damming-in or oil barriers).
Ensure adequate ventilation. Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose contaminated material as waste according to item 13. Do not flush with water or aqueous cleansing agents
Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Use only in well ventilated areas. Keep receptacles tightly sealed. Store in cool, dry place in tightly closed receptacles. Prevent formation of aerosols.
Store in cool, dry place in tightly closed receptacles. Protect from frost. Keep container tightly sealed.
Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. Only use chemical-protective gloves with CE-labelling of category III. Avoid direct contact with the chemical/ the product/ the preparation by organisational measures. Check protective gloves prior to each use for their proper condition. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. After use of gloves apply skin-cleaning agents and skin cosmetics. Material of gloves: Butyl rubber, BR. Recommended thickness of the material: ≥0.5 mm. For the mixture of chemicals mentioned below the penetration time has to be at least 480 minutes (Permeation according to EN 374 Part 3: Level ≥6). The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
Use suitable respiratory protective device when high concentrations are present. Not necessary if room is well-ventilated. Use suitable respiratory protective device in case of insufficient ventilation. Filter A/P2
Protective work clothing. Impervious protective clothing
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1993
- Shipping Name
- FLAMMABLE LIQUID, N.O.S. (ETHYLBENZENE, XYLENES)
- Transport Class
- 3 Flammable liquids.
- Packing Group
- III
Warning: Flammable liquids.
Warning: Flammable liquids.
Warning: Flammable liquids.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for CaFix seal?
The signal word is danger.
What is the physical form of CaFix seal?
CaFix seal is a fluid with according to product specification color. It has characteristic odor.
What is CaFix seal used for?
SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen) PROC10 Roller application or brushing Waterproofing
What are the hazard statements for CaFix seal?
This substance has 6 hazard statements:
- H226: Flammable liquid and vapour.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled.
- H372: Causes damage to organs through prolonged or repeated exposure.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of CaFix seal?
The melting point is Undetermined. and the boiling point is 137 °C.