Blitzdämmer®, Brunnen-Dämmer®, CableCem®, CemConex®-Mörtel, CEM-Rock®, Dämmer®, Depocrete®, DiWa-mix®, Drill-mix®, Ground-mix, GrowCem®, Hydrolith, HT, Jet-Mix®, MIXXAN®, Owalith, P4, Powercrete®, Procrete®, RBM, Recyclingbinder®, RM-Conline, Seku-mix®, Spezial-Fertigbeton (Zaunmörtel), Stabiflex / Biton, SWM, ThermoCem®, Tübbingmörtel, Ultrafin, WatCem, Zement/Bentonit-Gemisch

Seek fresh air. Dust should quickly be removed from throat and nose. Consult a physician, should symptoms such as discomfort, coughing or persistent irritation occur.

Symptoms: discomfort, coughing or persistent irritation

Remove dry product and rinse abundantly with water. Rinse wet product agent with plenty of water. Remove contaminated clothing, footwear, watches, etc. and clean these thoroughly before re-using them. Seek medical treatment in all cases of irritation or burns.

Symptoms: irritation on damp skin (due to sweating or humidity), skin irritation, dermatitis, or severe skin damage

Do not rub eyes dry, because mechanical stress may cause additional damage to the cornea. Where applicable, remove contact lenses and immediately rinse the eye, while open, under running water for at least 20 minutes in order to remove all particles. If possible, use isotonic eye-cleansing solution (0.9 % NaCl). Always consult an occupational physician or ophthalmologist.

Symptoms: serious and potentially irreversible eye damage

Do not induce vomiting. If the person is conscious, wash out mouth with water and give plenty of water to drink. Get immediate medical attention or contact the poison information center.

The products are not flammable.

The products are non-combustible and non-explosive and will not facilitate or sustain the combustion of other materials.

No specific measures are required, as the products do not pose any fire-related hazards.

Emergency action plans are not required.

The products should not penetrate the sewage water system, surface water or groundwater.

Dry product: Absorb spilled product and reuse, if possible. Use dry methods to clean. Wet product: Clean up wet product and place into a container. Allow material to dry and solidify before disposal.

Do not eat, drink, or smoke when working. Wear dust respirator and protective goggles in dusty environment. Use protective gloves to avoid skin contact.

The products should be stored under dry (minimizing internal condensation), water-protected conditions, clean and protected from contamination.

Do not eat, drink, or smoke when working. Wear dust respirator and protective goggles in dusty environment. Use protective gloves to avoid skin contact.

Not applicable.

Measures to prevent formation and spreading of dust, for example suitable ventilation systems and cleaning methods, which do not stir up dust.

Wear waterproof, abrasion, and alkali-resistant gloves. Leather gloves are not suitable due to their water penetrability and can release chromate-containing compounds. For handling the products, special gloves for chemicals (Cat. III) are not required. Investigations have proven that nitrile impregnated cotton gloves (layer thickness of about 0.15 mm) provide sufficient protection over a period of 480 minutes. Change soaked gloves. Have spare gloves ready.

Use tight-fitting safety goggles according to DIN EN 166:2002 where dust is formed or in case of risk of spilling.

Use adequate respirator masks when there is a risk that exposure limit values are exceeded (e.g., during open handling of dry powder products). Particle-filtering half-masks of the type FFP (according to DIN EN 149:2009) must be used.

Wear tight footwear and long-sleeved clothing. If contact with moist product cannot be avoided, protective clothing should also be waterproof. Take care that no moist product is running in shoes or boots from above. Observe skin protection plan. Apply skin care products, in particular after work.

Air: Compliance with dust emission limit values in accordance with the Technical Instructions on Air Quality. Water: Do not discharge the products into groundwater or wastewater systems in larger quantities. An increase in pH value is possible through exposure. At a pH value above 9, ecotoxicological effects may occur. Water directed or drained off into the wastewater system or surface water should therefore not lead to such a relevant pH value. Wastewater and groundwater regulations must be observed. Soil: Compliance with the German Federal Soil Protection Act (BBodSchG) and the German Federal Soil Protection and Contamination Ordinance (BBodSchV). No special control measures required.

The product is stable, as long as it is properly stored (see section 7). It should be kept dry. Contact with incompatible materials should be avoided.

The product is a hydraulic material. When mixed with water, an intended reaction takes place. As a result, the product hardens and forms a solid mass, which does not react with its environment.

Not applicable.

Moisture during storage can lead to lumping and loss of product quality.

Acids, ammonium salts, aluminum, or other base metals. Uncontrolled use of aluminum powder in wet product should be avoided as hydrogen is produced. The product dissolves in hydrofluoric acid, forming corrosive silicon tetrafluoride gas. The calcium silicates of the product may react with strongly oxidizing agents such as fluorides.

The product does not decompose into hazardous components.

Product exceeding the effective date of the reducing agent must be retreated or used in well-controlled, closed and fully automated processes. Unused dry product should be reused or cured with water. Moist products and sludge must be allowed to cure. Cured products should be disposed of in accordance with local official directives.

Do not dispose of in wastewater or surface water. Dispose of cured products like concrete waste and concrete sludge.