Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- PATTERN_RESIN_LS_Liquid
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Auxiliary for dental technology
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
GC EUROPE N.V.
manufacturer
Interleuvenlaan 33, B-3001 Leuven
+32/(0)16/74.10.00
Emergency Contacts
ChemTel Inc.
+01-813-248-0585
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Only substances required to be mentioned according to Annex II of regulation 1907/2006 are listed. Information on the other substances that may be present can be obtained upon request.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Methyl methacrylate | 80-62-6 | 50 - 75% | Yes |
| 2-Methoxyethyl methacrylate | 6976-93-8 | 10 - 25% | Yes |
| ethyl methacrylate | 97-63-2 | 5 - 10% | Yes |
| 2,2'-[(4-methylphenyl)imino]bisethanol | 3077-12-1 | 1 - 2.5% | Yes |
| Ethyleneglycol dimethacrylate | 97-90-5 | 1 - 2.5% | Yes |
| 2-(2H-benzotriazol-2-yl)-p-cresol | 2440-22-4 | 1 - 2.5% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist. Take affected persons into fresh air and keep quiet.
Immediately wash with water and soap and rinse thoroughly. Seek medical treatment. If skin irritation continues, consult a doctor.
Protect unharmed eye. Rinse opened eye for several minutes under running water. Then consult a doctor.
Rinse out mouth and then drink plenty of water. If symptoms persist consult doctor.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, sand, extinguishing powder.
Water
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Remove persons from danger area. Keep unprotected persons away.
Do not allow product to reach sewage system or any water course. Inform respective authorities in case of seepage into water course or sewage system. Do not allow to penetrate the ground/soil. In case of seepage into the ground inform responsible authorities. Prevent seepage into sewage system, workpits and cellars.
Absorb liquid components with liquid-binding material.
Materials: liquid-binding material
Related Products
Similar products with comparable safety profiles
PATTERN_RESIN_LS_Powder
---
RESINOLINE BD 2
CAS: 61790-12-3
TEROSON AL 7163 LIQUID APPLIED
---
CLEANING LIQUID, (ESL5)
---
A1 LP01 Liquid
---
Linx Solvent 1512
---
220035 220036 220236V 221236 DW Liquid
UFI: 4EKA-J1W3-7304-3UC6
RESION Polyester Laminating Resin
UFI: 2M00-A06D-Y005-AJU3
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with the eyes and skin.
Store in a cool, dry location. Keep receptacle tightly sealed. Protect from heat and direct sunlight. Store only in unopened original receptacles.
Keep ignition sources away - Do not smoke. Protect against electrostatic charges. Do not spray on a naked flame or any incandescent material.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Additional information about design of technical systems: No further data; see section 7.
Protective gloves. Material of gloves e.g. KCL Butoject 897 Butyl rubber, BR. Recommended thickness of the material: 0.29 mm. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. For the mixture of chemicals mentioned below the penetration time has to be at least 60 minutes (Permeation according to EN 16523-1:2015: Level 2). The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In the event that the limit exposure is exceeded, use a respiratory protective device with filter A. Suitable respiratory protective device recommended.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No decomposition if used according to specifications.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
12.1 Toxicity
No further relevant information available regarding aquatic toxicity.
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
12.6 Endocrine disrupting properties
12.7 Other adverse effects
12.2 Persistence and degradability
12.3 Bioaccumulative potential
No further relevant information available.
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
The substance is not considered to be PBT or vPvB.
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Results of PBT and vPvB assessment
12.6 Endocrine disrupting properties
Refers to section 11 for information on endocrine disrupting properties.
12.7 Other adverse effects
12.7 Other adverse effects
The product is classified as extremely hazardous for water (Water hazard class 3) and poses a risk to drinking water supplies.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
Must not be disposed of together with household garbage.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1247
- Shipping Name
- METHYL METHACRYLATE MONOMER, STABILIZED
- Transport Class
- 3 Flammable liquids
- Packing Group
- II
Warning: Flammable liquids
Warning: Flammable liquids
Warning: Flammable liquids
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for PATTERN_RESIN_LS_Liquid?
The signal word is danger.
What is the physical form of PATTERN_RESIN_LS_Liquid?
PATTERN_RESIN_LS_Liquid is a fluid appearing as liquid with clear color. It has characteristic odor.
What is the solubility of PATTERN_RESIN_LS_Liquid?
Fully miscible.
What is PATTERN_RESIN_LS_Liquid used for?
Auxiliary for dental technology
What are the hazard statements for PATTERN_RESIN_LS_Liquid?
This substance has 6 hazard statements:
- H225: Highly flammable liquid and vapour.
- H315: Causes skin irritation.
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H335: May cause respiratory irritation.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of PATTERN_RESIN_LS_Liquid?
The melting point is Undetermined. and the boiling point is 100 C.