Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Praestol™ 2650 DK FLOCCULANT
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Flocculant
Manufacturers & Suppliers
Solenis
manufacturer
Pesetastraat 62, 2991 XT Barendrecht, Netherlands
Solenis UK Industries Limited
manufacturer
P. O. Box 38, Cleckheaton Rd, Low Moor, Bradford, BD12 0JZ, United Kingdom
Emergency Contacts
Emergency Contact
+1-302-502-0991
Emergency Contact
112
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Notes
No hazardous ingredients
First Aid Measures
Emergency procedures for chemical exposure incidents
If breathed in, move person into fresh air. If unconscious, place in recovery position and seek medical advice. If symptoms persist, call a physician.
First aid is not normally required. However, it is recommended that exposed areas be cleaned by washing with soap and water.
Remove contact lenses. Protect unharmed eye.
Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician.
Medical Treatment
No hazards which require special first aid measures.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Water spray, Foam
Do not allow run-off from fire fighting to enter drains or water courses.
Product is compatible with standard fire-fighting agents.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Comply with all applicable federal, state, and local regulations.
For small spills, quickly contain and remove the spilled material using absorbent pads, socks, kitty litter, sawdust etc, then appropriately dispose.
Prevent further leakage or spillage if safe to do so.
The remaining residue or film can be treated with dilute caustic (2%) or dilute liquid bleach (2–5%), allowed to soak for up to one hour, and clean with warm water (between 49C – 54C (120F – 130 F)) or flushed to a sewer using high volumes of water taking into account local guidelines. Pick up and arrange disposal without creating dust.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid spillage on floor as the product can become very slippery. Avoid dust formation. Smoking, eating and drinking should be prohibited in the application area.
Electrical installations / working materials must comply with the technological safety standards.
Avoid breathing dust. Smoking, eating and drinking should be prohibited in the application area.
Take measures to prevent the build up of electrostatic charge.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide appropriate exhaust ventilation at places where dust is formed. General room ventilation should be adequate for normal conditions of use. However, if unusual operating conditions exist, provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below exposure guidelines (if applicable) or below levels that cause known, suspected or apparent adverse effects.
Wear resistant gloves (consult your safety equipment supplier).
Safety glasses
No personal respiratory protective equipment normally required.
Wear as appropriate: Safety shoes
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
No decomposition if stored and applied as directed.
Product will not undergo hazardous polymerization.
Keep away from heat, flame, sparks and other ignition sources.
Strong oxidizing agents
Carbon monoxide, Carbon dioxide (CO2), Nitrogen oxides (NOx)
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of in accordance with local regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not dangerous goods
- Shipping Name
- Not dangerous goods
- Transport Class
- Not dangerous goods
- Packing Group
- Not dangerous goods
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Praestol™ 2650 DK FLOCCULANT?
The signal word is no signal word.
What is the physical form of Praestol™ 2650 DK FLOCCULANT?
Praestol™ 2650 DK FLOCCULANT is a solid with white, off-white color. It has odourless odor.
What is Praestol™ 2650 DK FLOCCULANT used for?
Flocculant
What is the melting point of Praestol™ 2650 DK FLOCCULANT?
The melting point is No data available and the boiling point is No data available.