NextSDS Logo
Safety Data Sheet EN

ACPOven Shield

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
ACPOven Shield

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Cleaning agent / Cleaner Oven Cleaner

Uses advised against

No further relevant information available.

Manufacturers & Suppliers

C

Chemco Corporation

manufacturer

300 Canal St. Lawrence MA 01840 USA

(978) 687-9000

Emergency Contacts

ChemTel Inc.

(800)255-3924

ChemTel Inc.

+1 (813)248-0585

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Not Classified
H361 H361

GHS Pictograms

GHS08 - Serious health hazard

GHS08

Hazard Statements

H361 Suspected of damaging fertility or the unborn child.

Precautionary Statements

P281 Use personal protective equipment as required.
P301 + P330 + P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

Mixture of substances listed below with nonhazardous additions.

Chemical Name CAS Number Concentration Hazardous
polyethylene glycol EC: 500-038-2 25322-68-3 10 - 25% Yes
alcohols, C9-11, ethoxylated EC: 500-446-0 68439-46-3 10% Yes
Nonylphenoxy poly (ethyleneoxy 9)ethanol, branched EC: 500-209-1 68412-54-4 10% Yes

For the wording of the listed risk phrases refer to section 16.

Notes

Dangerous components: None in reportable quantities.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Supply fresh air; consult doctor in case of complaints.

Skin contact

Clean with water and soap. If skin irritation continues, consult a doctor.

Eye contact

Remove contact lenses if worn, if possible. Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.

Ingestion

Rinse out mouth and then drink plenty of water. Do not induce vomiting; call for medical help immediately.

Immediate Medical Attention

Medical supervision for at least 48 hours.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use fire extinguishing methods suitable to surrounding conditions.

Unsuitable media

None.

Specific hazards

No further relevant information available.

Firefighter Protection

Wear self-contained respiratory protective device. Wear fully protective suit.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Ensure adequate ventilation. Particular danger of slipping on leaked/spilled product. Wear protective equipment. Keep unprotected persons away.

Environmental

Do not allow to enter sewers/ surface or ground water.

Cleanup methods

Absorb with liquid-binding material

Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent formation of aerosols. Ensure good ventilation/exhaustion at the workplace.

Storage

Store in a cool location. Store in cool, dry conditions in well sealed receptacles. Protect from frost.

Fire prevention

Avoid storage near extreme heat, ignition sources or open flame.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

No further data; see item 7.

Hands

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact gloves made of the following materials are suitable: Butyl rubber, BR Neoprene gloves Nitrile rubber, NBR

Eyes

Safety glasses

Respiratory

Not necessary if room is well-ventilated. Use suitable respiratory protective device in case of insufficient ventilation. Use suitable respiratory protective device when aerosol or mist is formed. For spills, respiratory protection may be advisable.

Skin/Body

Light weight protective clothing

Environmental

No special requirements.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Explosive Limits
---
Odor Threshold
Not determined.
Density
0,98 g/cm³
Dynamic Viscosity
Not determined.
Cloud Point
---
Solubility
---
Flash Point
Not applicable.
Decomposition Temperature
Not determined.
Kinematic Viscosity
Not determined.
Properties Status
---
Upper Explosive Limit
Not determined.
State Under Standard Conditions
---
Crystallisation Point
---
Softening Point
---
Bulk Density
---
Freezing Point
---
Melting Point
Undetermined.
Physical State
Liquid
Form
Liquid
Voc Content
---
Molecular Weight
---
Solubility In Fat
---
Physical State Data
liquid
Relative Density
Not determined.
Partition Coefficient
Not determined.
Colour
Clear
Evaporation Rate
Not determined.
Odor
Alcohol-like
Auto Ignition Temperature
Not determined.
Relative Evaporation Rate
---
Solubility In Water
Fully miscible.
Ph
8,5-9
Colour Intensity
---
Metal Corrosion
---
Flammability
Not applicable.
Vapor Density
Not determined.
Solidification Point
---
Appearance
Form: Liquid Colour: Clear
Boiling Point
212 °F / 100 °C
Vapor Pressure
Not determined.
Lower Explosive Limit
Not determined.
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if used and stored according to specifications.

Hazardous reactions

Reacts with strong oxidizing agents. Reacts with strong acids.

Avoid

No further relevant information available.

Incompatible

No further relevant information available.

Decomposition

Sulphur oxides (SOx) Aldehyde Carbon monoxide and carbon dioxide

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

Treatment

Can be burned with household garbage after consulting with the waste disposal facility operator and the pertinent authorities and adhering to the necessary technical regulations. Smaller quantities can be disposed of with household waste.

Disposal

Can be burned with household garbage after consulting with the waste disposal facility operator and the pertinent authorities and adhering to the necessary technical regulations. Smaller quantities can be disposed of with household waste.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

Chemical Safety Assessment Not performed

Safety Data Sheet according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and GHS

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for ACPOven Shield?

The signal word is warning.

What is the physical form of ACPOven Shield?

ACPOven Shield is a liquid appearing as form: liquid colour: clear with clear color. It has alcohol-like odor.

What is ACPOven Shield used for?

Cleaning agent / Cleaner Oven Cleaner

What are the hazard statements for ACPOven Shield?

This substance has 1 hazard statement:

  • H361: Suspected of damaging fertility or the unborn child.

What is the melting point of ACPOven Shield?

The melting point is Undetermined. and the boiling point is 212 °F / 100 °C.