Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ACP Dirt Buster III Oven Cleaner
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Scouring agent/ Cleaning agent
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
Chemco Corporation
manufacturer
300 Canal St. Lawrence MA 01840 USA
(978) 687-9000
Emergency Contacts
ChemTel Inc.
(800)255-3924
ChemTel Inc.
+1 (813)248-0585
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2-aminoethanol EC: 205-483-3 | 141-43-5 | 10% | Yes |
| Disodium cocoamphodipropionate | 68604-71-7 | 10% | Yes |
| Dodecylbenzenesulphonic acid, compound with 2,2',2''-nitrilotriethanol (1:1) EC: 248-406-9 | 27323-41-7 | 10% | Yes |
| dodecylbenzenesulphonic acid, compound with 2-aminoethanol (1: 1) EC: 248-024-2 | 26836-07-7 | 10% | Yes |
| 1-(2-butoxy-1-methylethoxy)propan-2-ol EC: 249-951-5 | 29911-28-2 | 10% | No |
| methanol EC: 200-659-6 | 67-56-1 | 1% | Yes |
For the wording of the listed risk phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately rinse with water. If skin irritation continues, consult a doctor.
Remove contact lenses if worn, if possible. Rinse opened eye for several minutes under running water. Then consult a doctor.
Rinse out mouth and then drink plenty of water. Do not induce vomiting; call for medical help immediately.
Immediate Medical Attention
Call for medical help immediately (for swallowing). Medical supervision for at least 48 hours.
Medical Treatment
Medical supervision for at least 48 hours.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use fire extinguishing methods suitable to surrounding conditions.
None.
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Wear self-contained respiratory protective device. Wear fully protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away. Particular danger of slipping on leaked/spilled product.
Do not allow to enter sewers/ surface or ground water. Dilute with plenty of water.
Absorb with liquid-binding material
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Suma Grill D9 Oven & Grill Cleaner
---
Surface Cleaner Spray
---
Arcair Protex Alclean Aluminum Cleaner
---
Suma Auto Oven Clean D9.10
UFI: U1FJ-N125-200V-ET8G
Airco Cleaner
UFI: 26GX-F8N2-900R-NVHC
CILLIT BANG Power Cleaner- Degreaser
---
ARBO HIGH PRESSURE DEGREASER SUPER 50B
---
Surface Cleaner Pro
UFI: EC00-60HP-400F-G9RM
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Store in cool, dry conditions in well sealed receptacles. Protect from frost. Avoid storage near extreme heat, ignition sources or open flame.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact gloves made of the following materials are suitable: Rubber gloves
Contact lenses should not be worn. Safety glasses
Not necessary if room is well-ventilated. Use suitable respiratory protective device when aerosol or mist is formed. NIOSH or EN approved organic vapor respirator equipped with a dust/mist prefilter should be used.
Protective work clothing
No further relevant information available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications.
Reacts with strong oxidizing agents. Reacts with strong acids.
No further relevant information available.
No further relevant information available.
Carbon monoxide and carbon dioxide Sulphur oxides (SOx) Nitrogen oxides
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Smaller quantities can be disposed of with household waste. Can be burned with household garbage after consulting with the waste disposal facility operator and the pertinent authorities and adhering to the necessary technical regulations.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- Not Regulated
- Shipping Name
- Not Regulated
- Transport Class
- Not Regulated
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ACP Dirt Buster III Oven Cleaner?
The signal word is danger.
What is the physical form of ACP Dirt Buster III Oven Cleaner?
ACP Dirt Buster III Oven Cleaner is a liquid appearing as form: liquid, colour: red with red color. It has characteristic odor.
What is ACP Dirt Buster III Oven Cleaner used for?
Scouring agent/ Cleaning agent
What are the hazard statements for ACP Dirt Buster III Oven Cleaner?
This substance has 2 hazard statements:
- H315: Causes skin irritation.
- H318: Causes serious eye damage.
What is the melting point of ACP Dirt Buster III Oven Cleaner?
The melting point is Not Determined. and the boiling point is 212 °F / 100 °C.