SCL-500

Remove to open air. In the event of breathing difficulties, get medical advice/attention immediately.

Remove contaminated clothing. Wash immediately with plenty of water. If irritation persists, get medical advice/attention. Wash contaminated clothing before using it again.

Remove contact lenses, if present. Wash immediately with plenty of water for at least 15 minutes, opening the eyelids fully. If problem persists, seek medical advice.

Get medical advice/attention. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious person, unless authorised by a doctor.

carbon dioxide, foam, powder and water spray.

None in particular.

Do not breathe combustion products.

Use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health.

Block the leakage if there is no hazard.

The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Absorb the remainder with inert absorbent material.

Materials: inert absorbent material

Ensure that there is an adequate earthing system for the equipment and personnel. Avoid contact with eyes and skin. Do not breathe powders, vapours or mists. Do not eat, drink or smoke during use. Wash hands after use. Avoid leakage of the product into the environment.

Store only in the original container. Store in a ventilated and dry place, far away from sources of ignition. Keep containers well sealed. Keep the product in clearly labelled containers. Avoid overheating. Avoid violent blows. Keep containers away from any incompatible materials.

Do not eat, drink or smoke during use. Wash hands after use.

Store far away from sources of ignition.

As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration.

Protect hands with category III work gloves (see standard EN 374). The following should be considered when choosing work glove material: compatibility, degradation, failure time and permeability. The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on the duration and type of use.

Wear airtight protective goggles (see standard EN 166).

If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, use a mask with a type A filter whose class (1, 2 or 3) must be chosen according to the limit of use concentration. (see standard EN 14387). In the presence of gases or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required. Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the threshold values considered. The protection provided by masks is in any case limited. If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529.

Wear category II professional long-sleeved overalls and safety footwear (see Regulation 2016/425 and standard EN ISO 20344). Wash body with soap and water after removing protective clothing.

The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards.

The product is stable in normal conditions of use and storage.

There are no particular risks of reaction with other substances in normal conditions of use. 2-BUTOXYETHANOL: Decomposes under the effect of heat.

No hazardous reactions are foreseeable in normal conditions of use and storage. 2-BUTOXYETHANOL: May react dangerously with: aluminium, oxidising agents. Forms peroxides with: air.

None in particular. However the usual precautions used for chemical products should be respected. SODIUM HYDROXIDE: Avoid exposure to: air, moisture, sources of heat. 2-BUTOXYETHANOL: Avoid exposure to: sources of heat, naked flames.

SODIUM HYDROXIDE: Incompatible with: strong acids, ammonia, zinc, lead, aluminium, water, flammable liquids.

2-BUTOXYETHANOL: May develop: hydrogen.

Disposal must be performed through an authorised waste management firm, in compliance with national and local regulations.

Reuse, when possible. Product residues should be considered special hazardous waste.