VARNISH UV HIGH GLOSS

Remove the patient out of the contaminated area into the fresh air. If breathing is irregular or stops, administer artificial respiration. If the person is unconscious, place in appropriate recovery position. Keep the patient warm and at rest until medical attention arrives.

Symptoms: Inhalation produces irritation to mucus, coughing and breathlessness.

Remove immediately contaminated clothing and wash it separately with an alkaline detergent. Avoid concurrent exposure to sunlight or other sources of UV radiation which may increase skin sensitivity. Wash thoroughly the affected area with plenty of cold or lukewarm water and neutral soap, or use a suitable skin cleanser. Do not use solvents or thinners. In the case of skin reddening or rashes, contact a doctor immediately. Throw away clothing should it be highly contaminated.

Symptoms: Skin contact causes redness.

Remove contact lenses. Rinse eyes copiously by irrigation with plenty of clean, fresh water for at least 15 minutes, holding the eyelids apart, until the irritation is reduced. Avoid concurrent exposure to sunlight or other sources of UV radiation which may increase eye sensitivity. Call a physician immediately.

Symptoms: Contact with the eyes produces redness and pain.

Extinguishing powder or CO2. In the case of more important fires, also alcohol resistant foam and water spray/mist.

Combustible if heated. Irritant. Exposure to combustion or decomposition products may be a hazard to health. Pyrolyzed acrylates are highly irritant to the respiratory system.

If the fire-proof protective equipment is not available or is not being used, combat fire from a sheltered position or from a safe distance. Bear in mind the direction of the wind.

Eliminate possible sources of ignition and when appropriate, ventilate the area. Do not smoke. Avoid direct contact with this product.

In the case of large scale spills or when the product contaminates lakes, rivers or sewages, inform the appropriate authorities in accordance with local regulations.

Avoid contamination of drains, surface or subterranean water and soil.

Clean preferably with a biodegradable detergent.

Materials: non-combustible absorbent materials (earth, sand, vermiculite, diatomaceous earth, etc...)

Comply with the existing legislation on health and safety at work. Avoid any type of leakage or escape. Keep the container tightly closed. Do not eat, drink or smoke while handling. After handling, wash hands with soap and water.

Forbid the entry to unauthorized persons. This product should be stored isolated from heat and electrical sources. Do not smoke in storage area. Avoid direct contact with sunlight. Avoid extreme humidity conditions. In order to avoid leakages, the containers, after use, should be closed carefully and placed in a vertical position.

Do not eat, drink or smoke while handling. After handling, wash hands with soap and water.

Due to its flammability, this material should only be used in areas from which all naked lights and other sources of ignition have been excluded and away from other heat or electrical sources. Do not smoke.

Provide adequate ventilation. Where reasonably practicable, this should be achieved by the use of local exhaust ventilation and good general extraction.

Gloves resistant against chemicals (EN374). When repeated or prolonged contact with the product is expected, gloves of protection level 5 or higher should be used, with a breakthrough time of >240 min. When short contact with the product is expected, use gloves with a protection level 2 or higher should be used, with a breakthrough time >30 min. The breakthrough time of the selected glove material should be in accordance with the pretended period of use. There are several factors (for example, temperature), they do in practice the period of use of a protective gloves resistant against chemicals is clearly lower than the established standard EN374. Due to the wide variety of circumstances and possibilities, the instructions/specifications provided by the glove supplier should be taken into account. Do not use PVC gloves as PVC absorbs acrylates. Use the proper technique of removing gloves (without touching glove’s outer surface) to avoid contact of the product with the skin. The gloves should be immediately replaced when any sign of degradation is noted.

Safety goggles with suitable lateral protection (EN166). Clean daily and disinfect at regular intervals in accordance with the instructions of the manufacturer. Face shield against liquid splashes (EN166), advisable when there is a risk of spillage, diffusion or atomization of the liquid.

Mask for gases and vapours (EN14387). Class 1: low capacity up to 1000 ppm, Class 2: medium capacity up to 5000 ppm, Class 3: high capacity up to 10000 ppm. In order to obtain a suitable protection level, the filter class must be selected depending on the type and concentration of the contaminating agents present, in accordance with the specifications supplied by the filter producers.

Advisable. Barrier creams may help to protect the exposed areas of the skin. Barrier creams should not be applied once exposure has occurred.

Avoid any spillage in the environment. Spills on the soil: Prevent contamination of soil.

Stable under recommended storage and handling conditions.

Corrosivity to metals: It is not corrosive to metals. Pyrophorical properties: It is not pyrophoric.

Possible dangerous reaction with oxidizing agents, acids, alkalis, peroxides, polymerization initiators.

Heat: Keep away from sources of heat. Light: If possible, avoid direct contact with sunlight. Air: The product is not affected by exposure to air, but should not be left the containers open. Humidity: Avoid extreme humidity conditions. Pressure: Not relevant. Shock: The product is not sensitive to shocks, but as a recommendation of a general nature should be avoided bumps and rough handling to avoid dents and breakage of packaging, especially when the product is handled in large quantities, and during loading and download operations.

Keep away from oxidizing agents, from strongly alkaline and strongly acid materials.

As consequence of thermal decomposition, hazardous products may be produced: nitrogen oxides.

Take all necessary measures to prevent the production of waste whenever possible. Analyse possible methods for revaluation or recycling. Do not discharge into drains or the environment, dispose at an authorised waste collection point. Waste should be handled and disposed in accordance with current local and national regulations.

Controlled incineration in special facilities for chemical waste, in accordance with local regulations.

Ensure that persons transporting the product know what to do in case of accident or spill. Always transport in closed containers that are upright and secure.

Ensure that persons transporting the product know what to do in case of accident or spill. Always transport in closed containers that are upright and secure.

Ensure that persons transporting the product know what to do in case of accident or spill. Always transport in closed containers that are upright and secure.