Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
Everbuild Mitre Fast Activator is a aerosol substance commonly used adhesive.
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
Hazard Classifications
GHS Hazard Pictograms & Safety Symbols
GHS02
GHS07
GHS09
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H315: Causes skin irritation.
- H336: May cause drowsiness or dizziness.
- H411: Toxic to aquatic life with long lasting effects.
Precautionary Statements
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P211: Do not spray on an open flame or other ignition source.
- P251: Do not pierce or burn, even after use.
- P261: Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
- P273: Avoid release to the environment.
- P410 + P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/ 122 °F.
Manufacturers & Suppliers
Authorized suppliers, manufacturers, and distribution network information
Everbuild – A Sika Company
undefined
Site 41 Knowsthorpe Way Cross Green Industrial Estate Leeds West Yorkshire LS9 0SW United Kingdom
GB
0113 240 3456
24/7 Emergency Response
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
Emergency Contact
0044 113 240 3456
GB
(office hours only)
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
mixtureChemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Hydrocarbons, C6-C7, n-alkanes, isoalkanes, cyclics, <5% n-hexane | N/A | 25-40% | Hazardous |
| N,N-dimethyl-p-toluidine EC: 202-805-4 | 99-97-8 | 0.25-1% | Hazardous |
| petroleum gases, liquefied EC: 270-704-2 | 68476-85-7 | 25-40% | Hazardous |
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
Inhalation Exposure
Move to fresh air.
Symptoms:
May cause drowsiness or dizziness.
Skin Contact
Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. If symptoms persist, call a physician.
Symptoms:
Erythema, Dermatitis, irritant effects, Causes skin irritation.
Eye Contact
Remove contact lenses. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist.
Ingestion/Swallowing
Do not induce vomiting without medical advice. Rinse mouth with water. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person.
Medical Treatment
Treat symptomatically.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Exposure Controls & Personal Protective Equipment
Occupational exposure limits, engineering controls, and required safety equipment
Engineering Controls
Ensure adequate ventilation, especially in confined areas.
Hand Protection
Chemical-resistant, impervious gloves complying with an approved standard must be worn at all times when handling chemical products. Reference number EN 374. Follow manufacturer specifications. Suitable for short time use or protection against splashes: Butyl rubber/nitrile rubber gloves (0,4 mm). Suitable for permanent exposure: Viton gloves (0.4 mm), breakthrough time >30 min.
Eye Protection
Safety glasses with side-shields conforming to EN166
Respiratory Protection
Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. organic vapor (Type A) and particulate filter A1: < 1000 ppm; A2: < 5000 ppm; A3: < 10000 ppm P1: Inert material; P2, P3: hazardous substances. When workers are facing concentrations above the exposure limit they must use appropriate certified respirators.
Skin/Body Protection
Protective clothing (e.g. Safety shoes acc. to EN ISO 20345, long-sleeved working clothing, long trousers).
Environmental Exposure Controls
Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities.
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
UN Number
1950
Packing Group
Not assigned by regulation
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for Everbuild Mitre Fast Activator?
The signal word for this substance is "danger".
What is the physical form of Everbuild Mitre Fast Activator?
Everbuild Mitre Fast Activator is a aerosol appearing as aerosol with various color. It has no data available odor.
What is Everbuild Mitre Fast Activator used for?
Adhesive
What are the hazard statements for Everbuild Mitre Fast Activator?
This substance has 5 hazard statements: H222: Extremely flammable aerosol. H229: Pressurised container: May burst if heated. H315: Causes skin irritation. H336: May cause drowsiness or dizziness. H411: Toxic to aquatic life with long lasting effects.
What is the melting point of Everbuild Mitre Fast Activator?
The melting point is No data available and the boiling point is No data available.