Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Arcanol LOAD150
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricant
Uses advised against
None known.
Manufacturers & Suppliers
Schaeffler Technologies AG & Co. KG
manufacturer
Georg-Schäfer-Str. 30, 97421 Schweinfurt / GERMANY
+49 (0)9721 91 - 0
http://www.schaeffler.com
Emergency Contacts
Advisory body
+49 (0)89-19240
24h
EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 2,2,4-Trimethyl-1,2-dihydroxiquinoline, polymerizate | 26780-96-1 | 1 - 3% | Yes |
| Alkyl thiadiazole EC: 293-927-7 | 91648-65-6 | 3% | Yes |
| Lithium tetrahydroxyborate | --- | 1 - 2.9% | Yes |
| Zinc naphthenate EC: 282-762-6 | 84418-50-8 | 1 - 2.5% | Yes |
Notes
Contains less than 3% w/w DMSO-extract (only for mineral oils). It does not contain a component of the PRTR register (Pollutant Release and Transfer Register). Substances of Very High Concern - SVHC: substances are not contained or are below 0.1%.
First Aid Measures
Emergency procedures for chemical exposure incidents
Ensure supply of fresh air. In the event of symptoms seek medical treatment.
When in contact with the skin, clean with soap and water. Consult a doctor if skin irritation persists.
Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Seek medical advice immediately. Do not induce vomiting.
Immediate Medical Attention
Seek medical advice immediately. Injections through the skin resulting from contact with the product at high pressure constitute a major medical emergency.
Medical Treatment
Treat symptomatically. Forward this sheet to the doctor. Surgical exploration should be undertaken without delay. Thorough and extensive debridement of the wound and underlying tissue is necessary to minimise tissue loss and prevent or limit permanent damage.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Foam. Dry powder. Water spray jet. Carbon dioxide.
Full water jet.
Risk of formation of toxic pyrolysis products.
Firefighter Protection
Use self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
High risk of slipping due to leakage/spillage of product. Forms slippery surfaces with water.
Do not discharge into the drains/surface waters/groundwater. Prevent spread over a wide area (e.g. by containment or oil barriers).
Take up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use only in well-ventilated areas. No special measures necessary if used correctly. The product is combustible. Wash hands before breaks and after work. Use barrier skin cream. Cloths contaminated with product should not be kept in trouser pockets. Do not eat, drink or smoke when using this product.
Keep only in original container. Keep container tightly closed. Keep away from frost. Keep in a cool place. Store in a dry place.
Wash hands before breaks and after work. Use barrier skin cream. Do not eat, drink or smoke when using this product.
The product is combustible.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ensure adequate ventilation on workstation. General exposure limit for oil mist should be noted. Measurement methods for taking workplace measurements must meet the performance requirements of DIN EN 482. For example, recommendations are given in the IFA's list of hazardous substances.
> 0.4 mm Butyl rubber, >120 min (EN 374-1/-2/-3). The details concerned are recommendations. Please contact the glove supplier for further information.
If there is a risk of splashing: Safety glasses. (EN 166:2001)
Breathing apparatus in the event of aerosol or mist formation. Short term: filter apparatus, combination filter A-P1. (DIN EN 14387)
not applicable
Comply with applicable environmental regulations limiting discharge to air, water and soil.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal ambient conditions (ambient temperature).
No dangerous reactions known if used as directed.
Reactions with oxidizing agents. If product is heated above decomposition temperature toxic vapours may be released.
Strong heating.
Strong oxidizing agent.
No hazardous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
It is not possible to determine a waste code for this product in accordance with the European Waste Catalogue (EWC) since it is only possible to classify it according to how it is used by the customer. The waste code is to be determined within the EU in liaison with the waste-disposal operator.
Disposal in an incineration plant in accordance with the regulations of the local authorities.
Waste Codes
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
EEC-REGULATIONS: 1991/689 (2001/118); 2010/75; 2004/42; 648/2004; 1907/2006 (REACH); 1272/2008; 75/324/EEC (2016/2037/EC); (EU) 2015/830; (EU) 2016/131; (EU) 517/2014. TRANSPORT-NATIONAL REGULATIONS (GB): ADR (2019); IMDG-Code (2019, 39. Amdt.); IATA-DGR (2019) EH40/2005 Workplace exposure limits (Second edition, published December 2011). Observe employment restrictions for mothers-to-be and nursing mothers. Observe employment restrictions for young people.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Arcanol LOAD150?
The signal word is warning.
What is the physical form of Arcanol LOAD150?
Arcanol LOAD150 is a pasty with red color. It has characteristic odor.
What is Arcanol LOAD150 used for?
Lubricant
What are the hazard statements for Arcanol LOAD150?
This substance has 3 hazard statements:
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H412: Harmful to aquatic life with long lasting effects.
What is the melting point of Arcanol LOAD150?
The melting point is > 240°C (464°F) and the boiling point is No information available..