Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- JRCure 1110 (TPO-L)
Regulatory Identifiers
- CAS Number
- 84434-11-7 Check regulations →
- EC Number
- 282-810-6 Check regulations →
- REACH No.
- 01-2119987994-10-0004
Identified Uses
F-1: Formulation of preparations, IW-2: Industrial use, resulting in inclusion into or onto a matrix, IW-3: Industrial use of process regulators for polymerisation processes in production of resins, rubbers, polymers, PW-4: Wide dispersive indoor use of reactive substances in open systems
Uses advised against
No uses advised against are identified.
Manufacturers & Suppliers
Chemical Inspection & Regulation Service Limited
TIANJIN JIURI NEW MATERIALS CO.,LTD.
manufacturer
5-6F, Building C, Vision Hill, No.1 Gonghua Road, Huayuan Hi-tech Park, Tianjin, China
+86-22-23811185
Emergency Contacts
Emergency Contact
+353 (1) 477 3710
9:00a.m.-17:30p.m.
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethyl phenyl(2,4,6-trimethylbenzoyl)phosphinate EC: 282-810-6 | 84434-11-7 | 99.22% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical attention.
Wash thoroughly with soap and water. Obtain medical attention if soreness or redness persists. If skin irritation or rash occurs, get medical advice/attention.
Symptoms: Soreness, redness, skin irritation, or rash.
Immediately flood the eye with plenty of water for at least 15 minutes, holding the eye open. Remove contact lenses if possible. Obtain medical attention.
Rinse mouth and then drink plenty of water. Obtain medical attention if symptoms appear or if large quantities have been ingested.
Immediate Medical Attention
In all cases of doubt, or when symptoms persist, seek medical attention. If skin irritation or rash occurs, get medical advice/attention.
Medical Treatment
Treat according to symptoms (decontamination, vital functions), no known specific antidote.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, dry powder, foam.
Water jet.
In case of fire, the following can be released: harmful vapours.
Firefighter Protection
Self-contained breathing apparatus with full-face mask and full protective clothing (standard wear).
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary people away; isolate hazard area and deny entry. Stay up wind and keep out of low areas where vapour may accumulate and ignite.
Pick up with suitable absorbent material.
Pump off product.
Contain contaminated water/firefighting water.
Pump off product (large amounts); Pick up with suitable absorbent material (residues).
Materials: suitable absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in tightly closed containers in cool, dry, isolated, well-ventilated area. Avoid inhaling vapour. Avoid contact with eyes, skin and clothing. Suitable equipment for dealing with fires, spills and leaks must be readily available. Earth all equipment. Use explosion protected electrical equipment and lighting. Do not smoke eat or drink in areas of use and storage. Use closed-system transfers wherever possible. Earth (ground) lines and equipment used during transfer to reduce possibility of static spark initiated fire or explosion
cool, dry, well ventilated, out of direct sunlight and separated from oxidants and strong mineral acids. Store in original containers. Storage should be closed.
Do not eat, drink and smoke in work areas. Wash hands after use. Remove contaminated clothing and protective equipment before entering eating areas.
Take precautionary measures against static discharges. Earth all equipment. Use explosion protected electrical equipment and lighting. Earth (ground) lines and equipment used during transfer to reduce possibility of static spark initiated fire or explosion. Store away from sources of heat or ignition.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Handle in accordance with good industrial hygiene and safety practice.
Chemical resistant protective gloves (EN 374) Suitable materials short-term contact and/or splashes (recommended: At least protective index 2, corresponding > 30 minutes of permeation time according to EN 374) - butyl rubber (butyl) - 0.7 mm coating thickness - nitrile rubber (NBR) - 0.4 mm coating thickness - Supplementary note: The specifications are based on tests, literature data and information of glove manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g. temperature) it must be considered, that the practical usage of a chemical-protective glove in practice may be much shorter than the permeation time determined through testing. - Manufacturer's directions for use should be observed because of great diversity of types.
Safety goggles.
Suitable respiratory protection for higher concentrations or long-term effect: Gas filter for gases/vapours of organic compounds (boiling point >65 °C, e. g. EN 14387 Type A).
Standard work wear and safety boots for normal handling and use.
Avoid discharge into the environment. According to local regulations, Federal and official regulations.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is stable if stored and handled as prescribed/indicated.
The substance is stable under normal storage and handling conditions.
No hazardous reactions if stored and handled as prescribed/indicated.
Incompatible materials. High temperatures. Proximity to sources of ignition.
Avoid contact with strong acids, alkali or oxidizing agents.
No hazardous decomposition products if stored and handled as prescribed/indicated. In case of fire may release toxic gases/vapours, e.g. carbon monoxide (CO), carbon dioxide (CO2), phosphorous compounds.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
Dispose of in accordance with all applicable local and national regulations. Use recovery/recycling where feasible, otherwise incineration is the recommended method of disposal.
Use recovery/recycling where feasible, otherwise incineration is the recommended method of disposal.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Ethyl phenyl(2,4,6-trimethylbenzoyl)phosphinate)
- Transport Class
- 9
- Packing Group
- III
See section 2.2
See section 2.2
See section 2.2
Regulatory Information
Chemical regulations, safety assessments, and compliance status
Employment restrictions concerning young person must be observed. For use only by technically qualified individuals.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for JRCure 1110 (TPO-L)?
The signal word is warning.
What is the physical form of JRCure 1110 (TPO-L)?
JRCure 1110 (TPO-L) is a liquid appearing as liquid at 20°c and 101.3 kpa with yellow coloured color. It has not available odor.
What is the solubility of JRCure 1110 (TPO-L)?
Miscible in 2 -propanol, 1,2 -Dichlorethane, Tetrahydrofuran, Isobutylmethylketon,dimethylformamide; n-Heptan: 10.5g/100g at 20 °C; 13.7g/100g at 30 °C and 19.5g/100g at 40 °C
What is JRCure 1110 (TPO-L) used for?
F-1: Formulation of preparations, IW-2: Industrial use, resulting in inclusion into or onto a matrix, IW-3: Industrial use of process regulators for polymerisation processes in production of resins, rubbers, polymers, PW-4: Wide dispersive indoor use of reactive substances in open systems
What are the hazard statements for JRCure 1110 (TPO-L)?
This substance has 2 hazard statements:
- H317: May cause an allergic skin reaction.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of JRCure 1110 (TPO-L)?
The melting point is -12 °C and the boiling point is 257.4 °C.