Product Identification & Regulatory Data
Official chemical identifiers, CAS numbers, and regulatory compliance information
Basic Product Information
Regulatory Identifiers
Chemical Abstracts Service registry number - unique identifier for chemical substances
Uses Information
Overview
MOTIP CUT & DRILL LUBRICANT 500 ML is a light yellow substance commonly used su21 consumer uses: private households / general public / consumers; su22 professional uses: public domain (administration, education, entertainment, services, craftsmen); product category: corrosion inhibitor; process category: proc7 industrial spraying, proc11 non industrial spraying; application: lubricant.
Manage Your Safety Data Sheets
Organize and access your chemical safety data with ease.
GHS Hazard Classification & Safety Warnings
Globally Harmonized System (GHS) hazard pictograms, signal words, and safety classifications
Classification Status
Signal Word
Hazard Classifications
GHS Hazard Pictograms & Safety Symbols
GHS02
GHS08
GHS (Globally Harmonized System) pictograms indicate specific chemical hazard categories and safety precautions
Hazard Statements
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
Precautionary Statements
- P101: If medical advice is needed, have product container or label at hand.
- P102: Keep out of reach of children.
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P211: Do not spray on an open flame or other ignition source.
- P251: Do not pierce or burn, even after use.
- P260: Do not breathe spray.
- P410 + P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
- P501: Dispose of contents / container in accordance with regional regulations.
Manufacturers & Suppliers
Authorized suppliers, manufacturers, and distribution network information
European Aerosols B.V.
manufacturer
Wolfraamweg 2 NL-8471 XC Wolvega The Netherlands
NL
24/7 Emergency Response
Critical emergency contact numbers for chemical spills, exposure incidents, and medical emergencies
Emergency Contact
+31 (0)561-694400
NL
09:00h - 17:00h
NPIS National Poisons Information Centre
+44 0344 892 0111
GB
Chemical Composition & Hazardous Ingredients
Detailed component analysis, concentration ranges, and hazardous substance identification
Product Type
mixtureGeneral Composition
Mixture of substances listed below with nonhazardous additions.
Chemical Components & Hazardous Substances
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Distillates(petroleum), hydrotreated lightparaffinic EC: 265-158-7 | 64742-55-8 | 20-25% | Hazardous |
| N/A | N/A | 12.5-20% | Hazardous |
| propane EC: 200-827-9 | 74-98-6 | 12.5-20% | Hazardous |
| butane(containing < 0,1 % butadiene(203-450-8)) EC: 203-448-7 | 106-97-8 | 5-10% | Hazardous |
| isobutane(containing < 0,1 % butadiene(203-450-8)) EC: 200-857-2 | 75-28-5 | 5-10% | Hazardous |
Additional Information
The content of Benzene (EINECS-Nr. 200-753-7) in the ingredients is less than 0,1% (Note P Annex 1A 1272/2008 EU), so the classification as carcinogen need not to apply. For the wording of the listed hazard phrases refer to section 16.
Emergency First Aid Measures
Critical first aid procedures for chemical exposure incidents and medical emergencies
Inhalation Exposure
Supply fresh air; consult doctor in case of complaints.
Eye Contact
Rinse opened eye for several minutes under running water.
Ingestion/Swallowing
Drink plenty of water and provide fresh air. Call for a doctor immediately.
Fire Fighting Measures & Emergency Response
Fire suppression methods, extinguishing media, and firefighting safety procedures
Suitable Extinguishing Media
Use fire extinguishing methods suitable to surrounding conditions.
Specific Fire Hazards
During heating or in case of fire poisonous gases are produced.
Firefighter Protection Equipment
Mouth respiratory protective device.
Accidental Release Measures & Spill Response
Emergency spill cleanup procedures, containment methods, and environmental protection
Emergency Procedures
Mount respiratory protective device. Wear protective equipment. Keep unprotected persons away. Keep away from ignition sources.
Environmental Precautions
Do not allow to enter sewers/ surface or ground water.
Cleanup Methods
Dispose contaminated material as waste.
Related Chemical Substances & Alternative Products
Similar chemicals with comparable safety profiles and industrial applications
Technical Specifications & Material Properties
Physical state, chemical properties, melting point, boiling point, and material characteristics
Safe Handling & Storage Procedures
Industrial handling precautions, storage conditions, and workplace safety requirements
Handling Precautions
• Ensure good ventilation/exhaustion at the workplace.
• No special measures required.
• Keep respiratory protective device available.
Storage Conditions
• Observe official regulations on storing packagings with pressurised containers.
• Keep container tightly sealed.
Fire Prevention Measures
Do not spray onto a naked flame or any incandescent material. Keep ignition sources away - Do not smoke.
Exposure Controls & Personal Protective Equipment
Occupational exposure limits, engineering controls, and required safety equipment
Engineering Controls
No further data; see section 7.
Hand Protection
Not required.
Eye Protection
Not required.
Respiratory Protection
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device. Filter A2/P3
Chemical Stability & Reactivity Data
Chemical stability, hazardous reactions, and incompatible materials information
Chemical Stability
No decomposition if used according to specifications.
Reactivity
No further relevant information available.
Hazardous Reactions
No dangerous reactions known.
Conditions to Avoid
No further relevant information available.
Incompatible Materials
No further relevant information available.
Hazardous Decomposition Products
No dangerous decomposition products known.
Transportation & Shipping Information
UN numbers, shipping names, transport classes, and regulatory transport requirements
UN Number
UN1950
Proper Shipping Name
AEROSOLS
Transport Hazard Class
2.1
Packing Group
not regulated
Chemical Safety FAQ & Common Questions
Most frequently asked questions about safety, handling, storage, and regulatory compliance
What is the hazard signal word for MOTIP CUT & DRILL LUBRICANT 500 ML?
The signal word for this substance is "danger".
What is the physical form of MOTIP CUT & DRILL LUBRICANT 500 ML?
MOTIP CUT & DRILL LUBRICANT 500 ML is a aerosol appearing as light yellow with light yellow color. It has mineral-oil-like odor.
What is the solubility of MOTIP CUT & DRILL LUBRICANT 500 ML?
Not miscible or difficult to mix.
What is MOTIP CUT & DRILL LUBRICANT 500 ML used for?
SU21 Consumer uses: Private households / general public / consumers; SU22 Professional uses: Public domain (administration, education, entertainment, services, craftsmen); Product category: Corrosion inhibitor; Process category: PROC7 Industrial spraying, PROC11 Non industrial spraying; Application: Lubricant
What are the hazard statements for MOTIP CUT & DRILL LUBRICANT 500 ML?
This substance has 2 hazard statements: H222: Extremely flammable aerosol. H229: Pressurised container: May burst if heated.
What is the melting point of MOTIP CUT & DRILL LUBRICANT 500 ML?
The melting point is Not determined. and the boiling point is Not applicable, as aerosol..