SPECTRASYN 6

Move affected person to fresh air and keep warm and at rest in a position comfortable for breathing. Rinse nose and mouth with water. Get medical attention if symptoms are severe or persist. When breathing is difficult, properly trained personnel may assist affected person by administering oxygen. If breathing stops, provide artificial respiration. Get medical attention immediately.

After contact with skin, take off immediately all contaminated clothing, and wash immediately with plenty of water. Get medical attention if symptoms are severe or persist after washing. If product is injected into or under skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.

Symptoms: If product is injected into or under skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.

Rinse immediately with plenty of water. Remove any contact lenses and open eyelids wide apart. Continue to rinse for at least 15 minutes. Get medical attention if any discomfort continues.

Symptoms: May cause temporary eye irritation.

Rinse mouth thoroughly with water. Do not induce vomiting. Get medical attention if any discomfort continues.

Extinguish with alcohol-resistant foam, carbon dioxide, dry powder or water fog.

Do not use water jet as an extinguisher, as this will spread the fire.

When heated and in case of fire, toxic vapours/gases may be formed.

No action shall be taken without appropriate training or involving any personal risk. Cool containers exposed to heat with water spray and remove them from the fire area if it can be done without risk. Evacuate area.

Stop leak if safe to do so.

Do not discharge into drains or watercourses or onto the ground.

Absorb spillage with non-combustible, absorbent material. Collect and place in suitable waste disposal containers and seal securely.

Materials: non-combustible, absorbent material

Provide adequate ventilation. Wear protective clothing as described in Section 8 of this safety data sheet. Follow precautions for safe handling described in this safety data sheet. Avoid inhalation of vapours and contact with skin and eyes. Take care as floors and other surfaces may become slippery.

Store in tightly-closed, original container in a dry, cool and well-ventilated place. Only store in correctly labelled containers. Product is a static accumulator.

Product is a static accumulator. Take precautionary measures against static discharges. Ground/bond container and receiving equipment. Earth container and transfer equipment to eliminate sparks from static electricity.

Provide adequate ventilation. As this product contains ingredients with exposure limits, process enclosures, local exhaust ventilation or other engineering controls should be used to keep worker exposure below any statutory or recommended limits, if use generates dust, fumes, gas, vapour or mist.

Chemical-resistant, impervious gloves complying with an approved standard should be worn if a risk assessment indicates skin contact is possible. The most suitable glove should be chosen in consultation with the glove supplier/manufacturer, who can provide information about the breakthrough time of the glove material. To protect hands from chemicals, gloves should comply with European Standard EN374.

Eyewear complying with an approved standard should be worn if a risk assessment indicates eye contact is possible. The following protection should be worn: Tight-fitting safety glasses. Personal protective equipment for eye and face protection should comply with European Standard EN166.

No specific requirements are anticipated under normal conditions of use. Respiratory protection complying with an approved standard should be worn if a risk assessment indicates inhalation of contaminants is possible. Ensure all respiratory protective equipment is suitable for its intended use and is 'CE'-marked. If ventilation is inadequate, suitable respiratory protection must be worn. EN 136/140/141/145/143/149

Wear appropriate clothing to prevent any possibility of liquid contact and repeated or prolonged vapour contact.

Stable at normal ambient temperatures and when used as recommended.

See the other subsections of this section for further details.

Will not polymerise.

Avoid excessive heat for prolonged periods of time. Avoid heat, flames and other sources of ignition. Product is a static accumulator Take precautionary measures against static discharges.

Strong oxidising agents.

Does not decompose when used and stored as recommended. Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours. Oxides of the following substances: Carbon.

Waste should be treated as controlled waste.

Dispose of waste to licensed waste disposal site in accordance with the requirements of the local Waste Disposal Authority.