NextSDS Logo
Safety Data Sheet EN

ADDITIN RC 2540 440 D/1760S

Scan your chemical compliance

Free 10-second scan. Upload a document and check compliance instantly.

Scan Now
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
ADDITIN RC 2540 440 D/1760S
Product Code
230090, 230091, 230095
Chemical Name
Dialkyl Polysulfide

Regulatory Identifiers

CAS Number
N/A
02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

GHS Pictograms

Hazard Statements

Product poses little or no hazard if spilled and no unusual hazard if involved in a fire.
Irritating gases/fumes are given off during burning or thermal decomposition.
It is expected that this product will be essentially non-irritating to the eyes and skin and essentially non-toxic by ingestion.
Gases and fumes evolved during thermal processing or decomposition of this material may cause irritation to the upper respiratory tract.
Irritation of the respiratory tract may result in discomfort, and coughing.

Precautionary Statements

Use cold water spray to cool fire-exposed containers to minimize the risk of rupture.
Use water as fog or mist; solid streams may spread fire.

Manage your Safety Data Sheets

Organize and access chemical safety data with ease

Manage SDS
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

HAZARDOUS INGREDIENTS This material is not hazardous under the criteria of the Federal OSHA Hazard Communication Standard 29 CFR 1910.1200.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call a physician.

Symptoms: If breathing is difficult

Skin contact

Wash clothing and clean shoes before reuse. Immediately remove contaminated clothing and shoes. In case of skin contact, wash affected areas with soap and water. Get medical attention if irritation develops or persists.

Symptoms: irritation develops or persists

Eye contact

In case of contact, flush eyes with large quantities of water for at least 15 minutes. The eyelids should be held apart during irrigation to ensure thorough flushing of all eye tissue. Get medical attention.

Ingestion

Call a physician. If material is ingested, do not induce vomiting unless directed to do so by medical personnel. Get medical attention.

Immediate Medical Attention

Get medical attention if irritation develops or persists (for skin contact).

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water, Carbon Dioxide, Dry Chemical, Foam

Unsuitable media

A solid stream of water directed into the burning material could spread the fire.

Specific hazards

During a fire, irritating and toxic gases may be generated by thermal decomposition or combustion. Hydrogen sulfide (H2S) formation is possible after prolonged heating.

Instructions

A solid stream of water directed into the burning material could spread the fire. Evacuate non-emergency personnel to a safe area. Use cold water spray to cool fire exposed containers.

Firefighter Protection

Full emergency equipment with self-contained breathing apparatus and full protective clothing should be worn by firefighters.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Extinguish all ignition sources. Keep unnecessary personnel out of spill area. Emergency clean-up personnel should wear appropriate protection when entering the spill area for clean-up. Notify local health authorities and other appropriate agencies if such contamination should occur. Cover the spill with absorbent material such as sand, sweeping com pound or diatomaceous earth. Scoop up solid absorbent for waste disposal. Spill area can be washed with water. Ventilate area to remove vapors.

Environmental

Do not allow spilled or released material to enter ground water, waste water or soil.

Cleanup methods

Cover the spill with absorbent material... Scoop up solid absorbent for waste disposal. Spill area can be washed with water.

Materials: absorbent material such as sand, sweeping com pound or diatomaceous earth.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Keep away from heat, sparks and flames. Store in a dry place away from excessive heat. Keep container tightly closed when not in use. Avoid contact with skin or clothing. Avoid breathing dusts, vapors or mists. Handle in accordance with good industrial hygiene and safety practices.

Storage

Store at ambient conditions. Store in a dry place away from excessive heat. Keep container tightly closed when not in use.

Hygiene

Handle in accordance with good industrial hygiene and safety practices.

Fire prevention

Keep away from heat, sparks and flames. Storage area should be equipped with sprinkler system.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Use local exhaust ventilation if dusting or misting is a problem, to maintain air levels below the recommended exposure limit.

Hands

Permeation resistant gloves (neoprene, nitrile, or PVC)

Eyes

Safety glasses with side shields or goggles are recommended.

Respiratory

The specific respirator selected must be based on contamination levels found in the work place, must not exceed the working limits of the respirator and be jointly approved by the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration (NIOSH-MSHA). Air purifying respirator equipped with a full-face organic vapor and dust/mist cartridge if vapors are near or exceeding the exposure limits listed in Section 2. In areas of high concentrations, confined space or other poorly ventilated areas and for large spill clean-up sites, fresh air-line respirators or self-contained breathing apparatus should be used. Observe OSHA regulations for respirator use (29 CFR 1910.134.)

Skin/Body

impervious clothing (long sleeve shirts) are recommended.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Dynamic Viscosity
Approximately 50 mPa.s @ 104 °F (40 °C) DIN 51562
Relative Evaporation Rate
---
Physical State Data
liquid
Upper Explosive Limit
---
Flammability
---
Physical State
Liquid
Crystallisation Point
---
Lower Explosive Limit
---
Colour
Yellow
Explosive Limits
---
Odor
Characteristic
Form
---
Vapor Pressure
Not Established
Molecular Weight
---
Bulk Density
Approximately 8.34 lb/gal
Partition Coefficient
---
Solubility In Fat
---
Appearance
---
Voc Content
---
Solidification Point
---
Cloud Point
---
Kinematic Viscosity
---
Properties Status
---
Auto Ignition Temperature
---
Odor Threshold
Not Established
Colour Intensity
---
State Under Standard Conditions
---
Ph
Not Established
Evaporation Rate
Not Established
Density
---
Solubility
Soluble in mineral oils and synthetic base oils
Decomposition Temperature
---
Boiling Point
Not Established
Vapor Density
Not Established
Softening Point
---
Flash Point
---
Freezing Point
---
Solubility In Water
Essentially Insoluble
Melting Point
Not Applicable
Metal Corrosion
---
Relative Density
Approximately 1 @ 68 °F (20 °C) DIN 51757
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable

Hazardous reactions

Will not occur

Avoid

High Heat.

Incompatible

Oxidizing materials

Decomposition

By fire and/or thermal decomposition: hydrogen sulfide, sulfur dioxide, oxides of carbon, and other undetermined aliphatic fragments.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

Shipping Name
Dialkyl Polysulfide
?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for ADDITIN RC 2540 440 D/1760S?

The signal word is no signal word.

What is the physical form of ADDITIN RC 2540 440 D/1760S?

ADDITIN RC 2540 440 D/1760S is a liquid with yellow color. It has characteristic odor.

What is the solubility of ADDITIN RC 2540 440 D/1760S?

Soluble in mineral oils and synthetic base oils

What are the hazard statements for ADDITIN RC 2540 440 D/1760S?

This substance has 5 hazard statements:

  • Product poses little or no hazard if spilled and no unusual hazard if involved in a fire.
  • Irritating gases/fumes are given off during burning or thermal decomposition.
  • It is expected that this product will be essentially non-irritating to the eyes and skin and essentially non-toxic by ingestion.
  • Gases and fumes evolved during thermal processing or decomposition of this material may cause irritation to the upper respiratory tract.
  • Irritation of the respiratory tract may result in discomfort, and coughing.

What is the melting point of ADDITIN RC 2540 440 D/1760S?

The melting point is Not Applicable and the boiling point is Not Established.

Compliance Scanner

Scan your compliance