Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Frigutec® SiNO3
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Heat transfer fluid
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
HVL GmbH
manufacturer
79410 Badenweiler Germany
+49-7632-823480
Emergency Contacts
Vergiftungs-Informations-Zentrale Freiburg
+49 (0) 761 19240
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
GHS07
GHS08
Hazard Statements
Precautionary Statements
Manage your Safety Data Sheets
Organize and access chemical safety data with ease
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethanediol EC: 203-473-3 | 107-21-1 | 15 - 25% | Yes |
| disodium silicate pentahydrate EC: 229-912-9 | 10213-79-3 | 15 - 20% | Yes |
| Sodium nitrate EC: 231-554-3 | 7631-99-4 | 10 - 15% | Yes |
| [3-(2,3-epoxypropoxy)propyl]trimethoxysilane EC: 219-784-2 | 2530-83-8 | 3 - 5% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air or oxygen; call for doctor. In case of unconsciousness place patient stably in side position for transportation.
Immediately rinse with water. Call a doctor immediately.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Call a doctor immediately.
Rinse out mouth and then drink plenty of water. Do NOT induce vomiting. Call for a doctor immediately.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO₂, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
Water with full jet
Formation of toxic gases is possible during heating or in case of fire.
Cool endangered receptacles with water spray.
Firefighter Protection
Wear self-contained respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Ensure adequate ventilation. Wear protective clothing.
Dilute with plenty of water. Do not allow to enter sewers/ surface or ground water.
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Use neutralising agent. Dispose of the material collected according to regulations.
Materials: liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust)
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Store in cool, dry conditions in well sealed receptacles.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see section 7.
Protective gloves Only use chemical-protective gloves with CE-labelling of category III. DIN EN 374 The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: - Butyl rubber (0.7 mm) - Nitrile rubber (0.4 mm) The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material ≥ 30 min The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Tightly sealed goggles
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
Protective work clothing
No further relevant information available.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN1760
- Shipping Name
- CORROSIVE LIQUID, N.O.S. (DISODIUM TRIOXOSILICATE)
- Transport Class
- 8 Corrosive substances.
- Packing Group
- II
Warning: Corrosive substances.
Warning: Corrosive substances.
Warning: Corrosive substances.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Frigutec® SiNO3?
The signal word is danger.
What is the physical form of Frigutec® SiNO3?
Frigutec® SiNO3 is a liquid with according to product specification color. It has characteristic odor.
What is the solubility of Frigutec® SiNO3?
water: Fully miscible.
What is Frigutec® SiNO3 used for?
Heat transfer fluid
What are the hazard statements for Frigutec® SiNO3?
This substance has 4 hazard statements:
- H290: May be corrosive to metals.
- H314: Causes severe skin burns and eye damage.
- H335: May cause respiratory irritation.
- H373: May cause damage to the kidneys through prolonged or repeated exposure. Route of exposure: Oral.
What is the melting point of Frigutec® SiNO3?
The melting point is Not determined. and the boiling point is Not determined..