POTASSIUM TRIPOLYPHOSPHATE SOLUTION

If breathing stops, give artificial respiration and seek immediate medical attention. Take the victim into open air; keep them warm and calm. If breathing is irregular or stops, perform artificial respiration.

Remove contaminated clothing.

Remove contact lenses, if present and if it is easy to do. Wash eyes with plenty of clean and cool water for at least 10 minutes while pulling eyelids up, and seek medical assistance.

Keep calm. NEVER induce vomiting.

Extinguisher powder or CO2. In case of more serious fires, also alcohol-resistant foam and water spray.

Do not use a direct stream of water to extinguish. In the presence of electrical voltage, you cannot use water or foam as extinguishing media.

Exposure to combustion or decomposition products can be harmful to your health.

Use water to cool tanks, cisterns, or containers close to the heat source or fire. Take wind direction into account.

Product not classified as hazardous for the environment, avoid spillage as much as possible.

clean the area immediately with a suitable decontaminant.

The product does not require special handling measures, the following general measures are recommended: For personal protection, see section 8. In the application area, smoking, eating, and drinking must be prohibited. Follow legislation on occupational health and safety. Never use pressure to empty the containers. They are not pressure-resistant containers. Keep the product in containers made of a material identical to the original.

The product does not require special storage measures. As general storage measures, sources of heat, radiation, electricity and contact with food should be avoided. Store the containers between 0 and 40 °C, in a dry and well-ventilated place. Store according to local legislation. Observe indications on the label. Once the containers are open, they must be carefully closed and placed vertically to prevent spills.

In the application area, smoking, eating, and drinking must be prohibited.

PPE: Non-disposable protective gloves against chemicals. Characteristics: «CE» marking, category III. Check the list of chemicals for which the glove has been tested. CEN standards: EN 374-1, En 374-2, EN 374-3, EN 420. Maintenance: A schedule for the periodical replacement of gloves should be established in order to guarantee their replacement before pollutants permeate them. The use of contaminated gloves could be more dangerous than not using gloves, since the pollutant can gradually accumulate in the glove's material. Observations: They are to be replaced whenever tears, cracks or deformations are observed or when exterior dirt could reduce their strength. Material: PVC (polyvinyl chloride). Breakthrough time (min.): > 480. Material thickness (mm): 0,35.

PPE: Protective goggles with built-in frame. Characteristics: «CE» marking, category II. Eye protector with built-in frame for protection against dust, smoke, fog and vapour. CEN standards: EN 165, EN 166, EN 167, EN 168. Maintenance: Visibility through lenses should be ideal. Therefore, these parts should be cleaned daily. Protectors should be disinfected periodically following the manufacturer's instructions. Observations: Some signs of wear and tear include: yellow colouring of the lenses, superficial scratching of the lenses, scraping etc.

PPE: Filter mask for protection against gases and particles. Characteristics: «CE» marking, category III. The mask must have a wide field of vision and an anatomically designed form in order to be sealed and watertight. CEN standards: EN 136, EN 140, EN 405. Maintenance: Should not be stored in places exposed to high temperatures and damp environments before use. Special attention should be paid to the state of the inhalation and exhalation valves in the face adaptor. Observations: Read carefully the manufacturer's instructions regarding the equipment's use and maintenance. Attach the necessary filters to the equipment according to the specific nature of the risk (Particles and aerosols: P1-P2-P3, Gases and vapours: A-B-E-K-AX), changing them as advised by the manufacturer. Filter Type needed: A2.

PPE: Chemical protective clothing. Characteristics: «CE» marking, category III. Clothing should fit properly. The level of protection must be set according to a test parameter called BT (Breakthrough Time), which indicates how long it takes for the chemical to pass through the material. CEN standards: EN 464, EN 340, EN 943-1, EN 943-2, EN ISO 6529, EN ISO 6530, EN 13034. Maintenance: In order to guarantee uniform protection, follow the washing and maintenance instructions provided by the manufacturer. Observations: The protective clothing's design should facilitate correct positioning, staying in place without moving for the period of use expected, bearing in mind environmental factors as well as any movement or position the user might adopt while carrying out the activity. PPE: Anti-static safety footwear against chemicals. Characteristics: «CE» marking, category III. Check the list of chemicals against which the footwear is resistant. CEN standards: EN ISO 13287, EN 13832-1, EN 13832-2, EN 13832-3, EN ISO 20344, EN ISO 20345. Maintenance: For correct maintenance of this kind of safety footwear, it is necessary to observe the instructions specified by the manufacturer. The footwear should be replaced as soon as any sign of damage is observed. Observations: The footwear should be cleaned regularly and dried when damp, although it should not be placed too close to a source of heat in order to avoid any sharp changes in temperature.

Unstable in contact with: Acids.

The product does not present hazards by their reactivity.

Neutralization can occur on contact with acids.

Avoid contact with acids.

Acids.

Depending on conditions of use, can be generated the following products: Corrosive vapors or gases.