Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- METAFLUX 70-3500 ROST-I-SOL®-Spray
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Coating material
Manufacturers & Suppliers
Techno Service GmbH
manufacturer
Detmolder Strasse 515, D-33605 Bielefeld, Germany
+49 521 924440
http://www.metaflux.de
Emergency Contacts
TSF
+49 70024112112
24h
TSF
+1 872 5888271
24h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Polymeric filmformers, additives, organic solvents, water, propellant.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Wash with water and soap
Symptoms: Generally the product does not irritate the skin.
Rinse opened eye for several minutes under running water. Then consult a doctor.
Rinse out mouth and then drink plenty of water. Seek medical treatment.
Immediate Medical Attention
Seek medical treatment.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
During heating or in case of fire poisonous gases are produced. Risk of bursting in case of fire heat
Firefighter Protection
Mouth respiratory protective device. Wear fully protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away. Particular danger of slipping on leaked/spilled product. Keep sources of ignition (flames, sparks, etc.) away. Do not use engines near by (potential source of ignition). Ensure adequate ventilation.
Do not allow to enter sewers/ surface or ground water.
Absorb liquid components
Materials: liquid-binding material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Ensure good ventilation/exhaustion at the workplace. Avoid inhalation and contact with the skin and the eyes.
Observe official regulations on storing packagings with pressurised containers. Keep container tightly sealed.
Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Material of gloves If contamination is possible, use gloves made of nitrile according EN 374. Penetration time of glove material >480 min / 0,9mm
Safety glasses
Use suitable respiratory protective device in case of insufficient ventilation. Use filter AX (EN 14387) for low boling organic vapors / gases (bp < 65°C).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Risk of bursting at temperatures >50°C.
No further relevant information available.
By use or incidental release the formation of explosive vapor/air mixtures is possible.
Temperatures >50°C, Avoid the use in the near of ignition sources.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Packing Group
- Void
Warning: Gases.
Warning: Gases.
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for METAFLUX 70-3500 ROST-I-SOL®-Spray?
The signal word is danger.
What is the physical form of METAFLUX 70-3500 ROST-I-SOL®-Spray?
METAFLUX 70-3500 ROST-I-SOL®-Spray is a aerosol appearing as aerosol, black with black color. It has ether like odor.
What is METAFLUX 70-3500 ROST-I-SOL®-Spray used for?
Coating material
What are the hazard statements for METAFLUX 70-3500 ROST-I-SOL®-Spray?
This substance has 1 hazard statement:
- H222: Extremely flammable aerosol. Pressurised container: May burst if heated.
What is the melting point of METAFLUX 70-3500 ROST-I-SOL®-Spray?
The melting point is Undetermined. and the boiling point is -24°C.