Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MFW30/G Spray Dried Flux
- Product Code
- 90200091
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
KMCI Ltd
manufacturer
Laguna Clay Company
distributor
14400 Lomitas Ave City of Industry, CA 91746
1-800-4Laguna
http://www.lagunaclay.com
Emergency Contacts
Emergency Contact
01782 744335
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
GHS07
GHS08
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mineralogical: Typical composition
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Quartz EC: 238-878-4 | 14808-60-7 | 20% | No |
| Albite EC: 270-666-7 | 68476-25-5 | 52% | No |
| Orthoclase EC: 270-666-7 | 68476-25-5 | 27% | No |
Physical: Supplied either a) As a milled suspension in water (slop) having a nominal solids content of 60%, or b) As a semi-dry granulate having a nominal solids content of 90%.
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove to fresh air.
Wash with soap and water.
Wash with copious amounts of clean water.
Wash out mouth thoroughly with water. Drink plenty of water.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Non Combustible.
No special fire-fighting equipment or measures required.
Firefighter Protection
No special fire-fighting equipment or measures required.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Slop spillages should be removed with copious amounts of water to the factory drainage system, observing effluent control limits. Spillage of semi-dry or dry product should be removed by vacuum methods.
Slop spillages should be removed with copious amounts of water to the factory drainage system, observing effluent control limits. Spillage of semi-dry or dry product should be removed by vacuum methods.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Observe good standards of industrial hygiene, and take care to prevent generation of air-borne dust.
Observe good standards of industrial hygiene.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Where dried product is involved ventilation should be adequate to ensure that Occupational Exposure Limits are not exceeded, or Local Exhaust Ventilation provided.
gloves are used to minimise physical exposure to the product
Should ventilation measures be found to be unsatisfactory, approved respiratory protection equipment should be worn.
protective clothing... to minimise physical exposure to the product
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No known hazardous reactions
No known decomposition products
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MFW30/G Spray Dried Flux?
The signal word is danger.
What is the physical form of MFW30/G Spray Dried Flux?
MFW30/G Spray Dried Flux is a off white powder appearing as off white powder - may be in slop or semi-dry broken cake. (an organic identification dyestuff may be added). with off white color. It has odourless odor.
What are the hazard statements for MFW30/G Spray Dried Flux?
This substance has 5 hazard statements:
- H302: Ingestion: Product is of low acute toxicity.
- H316: Eye Contact: Can produce physical irritation and inflammation.
- H316: Skin Contact: Waterground products can produce slight irritation.
- H334: Inhalation: As supplied the product does not give rise to a significant health risk. However when dry, excessive exposure to the dust may result in symptoms of chronic pulmonary disease.
- Spillage's of slop product onto floors may constitute a slipping hazard
What is the melting point of MFW30/G Spray Dried Flux?
The melting point is Above 1150°C .