Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- WÜRTH BRAKE CLEANER SPRAY 500ML
- Product Code
- 00890 108 7
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- NWNC-J02C-600X-0DN6
Identified Uses
Professional use product, Cleaning agent, Detergent
Uses advised against
Not applicable
Manufacturers & Suppliers
Würth SA (Pty) Ltd
distributor
G1 Isando Industrial Park, Gewel Street, Isando Ext. 3, 1600 Gauteng
+27 11 281-1000
Emergency Contacts
Advisory office in case of poisoning
+27 11 922-1164
Würth SA (Pty) Ltd
+27 11 281-1000
08:00-16:30 h
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS09
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Carbon dioxide EC: 204-696-9 | 124-38-9 | 1 - 10% | Yes |
| Hydrocarbons, C6-C7, n-alkanes, isoalkanes, cyclics, <5% n-hexane | --- | 90 - 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If inhaled, remove to fresh air. Get medical attention if symptoms occur.
In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Symptoms: Causes skin irritation.
Flush eyes with water as a precaution. Get medical attention if irritation develops and persists.
If swallowed, DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water.
Immediate Medical Attention
In the case of accident or if you feel unwell, seek medical advice immediately. When symptoms persist or in all cases of doubt seek medical advice.
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, Alcohol-resistant foam, Carbon dioxide (CO2), Dry chemical
High volume water jet
Flash back possible over considerable distance. Vapours may form explosive mixtures with air. Exposure to combustion products may be a hazard to health. If the temperature rises there is danger of the vessels bursting due to the high vapor pressure.
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus. Use personal protective equipment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Follow safe handling advice (see section 7) and personal protective equipment recommendations (see section 8).
For large spills, provide dyking or other appropriate containment to keep material from spreading. If dyked material can be pumped, store recovered material in appropriate container.
Avoid release to the environment. Prevent further leakage or spillage if safe to do so.
Soak up with inert absorbent material. Clean up remaining materials from spill with suitable absorbent.
Materials: inert absorbent material
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Do not get on skin or clothing. Avoid breathing spray. Do not swallow. Avoid contact with eyes. Wash skin thoroughly after handling. Handle in accordance with good industrial hygiene and safety practice, based on the results of the workplace exposure assessment. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Take precautionary measures against static discharges. Take care to prevent spills, waste and minimize release to the environment. Do not spray on an open flame or other ignition source.
Store locked up. Keep in a cool, well-ventilated place. Store in accordance with the particular national regulations. Do not pierce or burn, even after use. Keep cool. Protect from sunlight.
If exposure to chemical is likely during typical use, provide eye flushing systems and safety showers close to the working place. When using do not eat, drink or smoke. Wash contaminated clothing before re-use.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Take precautionary measures against static discharges. Do not spray on an open flame or other ignition source.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Minimize workplace exposure concentrations. If sufficient ventilation is unavailable, use with local exhaust ventilation. If advised by assessment of the local exposure potential, use only in an area equipped with explosion-proof exhaust ventilation.
Material: Nitrile rubber, Break through time: > 480 min, Glove thickness: > 0,45 mm
Safety glasses
If adequate local exhaust ventilation is not available or exposure assessment demonstrates exposures outside the recommended guidelines, use respiratory protection. Filter type: Self-contained breathing apparatus
Select appropriate protective clothing based on chemical resistance data and an assessment of the local exposure potential. If assessment demonstrates that there is a risk of explosive atmospheres or flash fires, use flame retardant antistatic protective clothing. Skin contact must be avoided by using impervious protective clothing (gloves, aprons, boots, etc).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under normal conditions.
Not classified as a reactivity hazard.
Extremely flammable aerosol. Vapours may form explosive mixture with air. If the temperature rises there is danger of the vessels bursting due to the high vapor pressure. Can react with strong oxidizing agents.
Heat, flames and sparks.
Oxidizing agents
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2
- Packing Group
- Not assigned by regulation
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for WÜRTH BRAKE CLEANER SPRAY 500ML?
The signal word is danger.
What is the physical form of WÜRTH BRAKE CLEANER SPRAY 500ML?
WÜRTH BRAKE CLEANER SPRAY 500ML is a aerosol containing a compressed gas appearing as aerosol containing a compressed gas with colourless color. It has hydrocarbon-like odor.
What is WÜRTH BRAKE CLEANER SPRAY 500ML used for?
Professional use product, Cleaning agent, Detergent
What are the hazard statements for WÜRTH BRAKE CLEANER SPRAY 500ML?
This substance has 5 hazard statements:
- H222: Extremely flammable aerosol.
- H229: Pressurised container: May burst if heated.
- H315: Causes skin irritation.
- H336: May cause drowsiness or dizziness.
- H411: Toxic to aquatic life with long lasting effects.
What is the melting point of WÜRTH BRAKE CLEANER SPRAY 500ML?
The melting point is No data available and the boiling point is Not applicable.