Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- AEROSIL® 200
- Chemical Name
- Silicon dioxide, chemically prepared
Regulatory Identifiers
- CAS Number
- 112945-52-5, 7631-86-9 Check regulations →
Identified Uses
Sealants, Coloured printing inks, Paints and varnishes., Adhesive, Silicone rubber, Cosmetic ingredient, Cosmetics, Agrochemicals. Function: Anticaking agent, Antiblocking agents, Coating agent, Dispersing agent, Flow-promoting agent., Reinforcing agent., Carrier
Manufacturers & Suppliers
Evonik Corporation USA
manufacturer
299 Jefferson Road, Parsippany, NJ 07054-0677, USA
973-929-8000
Emergency Contacts
CHEMTREC - US & CANADA
800-424-9300
CHEMTREC MEXICO
01-800-681-9531
CHEMTREC INTERNATIONAL
+1 703-527-3887
Product Regulatory Services
973-929-8060
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Silicon dioxide, chemically prepared | 112945-52-5 | 100% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move victims into fresh air.
Symptoms: cough, sneezing
Wash off with soap and plenty of water.
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes or until all material has been removed. Obtain medical attention.
If accidentally swallowed, rinse mouth thoroughly with water and afterwards, drink plenty of water. In case of discomfort, obtain medical attention.
Immediate Medical Attention
Obtain medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray, foam, CO2, dry powder., Adapt fire-extinguishing measures to surroundings
Do not use full-force water jet in order to avoid dispersal and spread of the fire.
None known.
Firefighter Protection
As in any fire, wear self-contained positive-pressure breathing apparatus, (MSHA/NIOSH approved or equivalent) and full protective gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Obey relevant local, state, provincial and federal laws and regulations. Do not contaminate any lakes, streams, ponds, groundwater or soil. Do not allow entrance in sewage water, soil stretches of water, groundwater, drainage systems.
Sweep up or vacuum up spillage and collect in suitable container for disposal.
Materials: suitable container
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Use with adequate ventilation.
Keep containers tightly closed in a dry, cool place.
Take precautionary measures against static discharges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Use impermeable gloves.
Wear safety glasses with side shields. In case dusts are formed, wear close fitting protective goggles.
A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 or applicable federal/provincial requirements must be followed whenever workplace conditions warrant respirator use. NIOSH's "Respirator Decision Logic" may be useful in determining the suitability of various types of respirators.
A safety shower and eye wash fountain should be readily available. To identify additional Personal Protective Equipment (PPE) requirements, it is recommended that a hazard assessment in accordance with the OSHA PPE Standard (29CFR1910.132) be conducted before using this product.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
No dangerous reaction known under conditions of normal use.
Possibility of hazardous reactions See Sect. 10.1 Reactivity. Product will not undergo hazardous polymerization.
No dangerous reaction known under conditions of normal use. Operations that create dust.
None known.
None known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for AEROSIL® 200?
The signal word is no signal word.
What is the physical form of AEROSIL® 200?
AEROSIL® 200 is a solid with white color. It has odorless odor.
What is AEROSIL® 200 used for?
Sealants, Coloured printing inks, Paints and varnishes., Adhesive, Silicone rubber, Cosmetic ingredient, Cosmetics, Agrochemicals. Function: Anticaking agent, Antiblocking agents, Coating agent, Dispersing agent, Flow-promoting agent., Reinforcing agent., Carrier
What is the melting point of AEROSIL® 200?
The melting point is ca. 1700 °C and the boiling point is not determined.