IMAPUR 1999/25 D

Remove to open air. In the event of breathing difficulties, get medical advice/attention immediately.

Remove contaminated clothing. Wash immediately with plenty of water. If irritation persists, get medical advice/attention. Wash contaminated clothing before using it again.

Remove contact lenses, if present. Wash immediately with plenty of water for at least 15 minutes, opening the eyelids fully. If problem persists, seek medical advice.

Get medical advice/attention. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious person, unless authorised by a doctor.

carbon dioxide, foam, chemical powder. For product loss or leakage that has not caught fire, water spray can be used to disperse flammable vapours and protect those trying to stem the leak.

Do not use jets of water. Water is not effective for putting out fires but can be used to cool containers exposed to flames to prevent explosions.

Excess pressure may form in containers exposed to fire at a risk of explosion. Do not breathe combustion products.

Use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health.

Block the leakage if there is no hazard.

The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Absorb the remainder with inert absorbent material.

Materials: inert absorbent material

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters. Avoid bunching of electrostatic charges. Do not eat, drink or smoke during use. Remove any contaminated clothes and personal protective equipment before entering places in which people eat.

Store only in the original container. Store in a well ventilated place, keep far away from sources of heat, naked flames and sparks and other sources of ignition.

Do not eat, drink or smoke during use. Remove any contaminated clothes and personal protective equipment before entering places in which people eat.

Keep away from heat, sparks and naked flames; do not smoke or use matches or lighters.

As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration.

Protect hands with category III work gloves (see standard EN 374). The following should be considered when choosing work glove material: compatibility, degradation, failure time and permeability. The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on the duration and type of use.

Wear airtight protective goggles (see standard EN 166). In the presence of risks of exposure to splashes or squirts during work, adequate mouth, nose and eye protection should be used to prevent accidental absorption.

If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, use a mask with a type A filter whose class (1, 2 or 3) must be chosen according to the limit of use concentration. (see standard EN 14387). In the presence of gases or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required. Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the threshold values considered. The protection provided by masks is in any case limited. If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529.

Wear category II professional long-sleeved overalls and safety footwear (see Directive 89/686/EEC and standard EN ISO 20344). Wash body with soap and water after removing protective clothing.

The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards.

The product is stable in normal conditions of use and storage.

There are no particular risks of reaction with other substances in normal conditions of use. DIMETHYL FORMAMIDE: decomposes on contact with flames and hot surfaces to generate toxic fumes.

The vapours may also form explosive mixtures with the air. DIMETHYL FORMAMIDE: risk of explosion on contact with: alkaline metals, strong oxidising agents, bromine, chlorine, triethyl aluminium, alkaline nitrides. Can react violently with: reducing agents, halogens, nitrates, metal and non-metal oxides, halogenated hydrocarbons. Forms explosive mixtures with air when warm.

Avoid overheating. Avoid bunching of electrostatic charges. Avoid all sources of ignition. DIMETHYL FORMAMIDE: avoid exposure to sources of heat and naked flames.

DIMETHYL FORMAMIDE: oxidising substances, halogenated hydrocarbons, inorganic nitrates, triethyl aluminium, bromine, chlorine and iron.

In the event of thermal decomposition or fire, gases and vapours that are potentially dangerous to health may be released. DIMETHYL FORMAMIDE: nitric oxides, dimethylamine, hydrogen cyanide.