Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- IMAPUR HS 03/E
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Solvent-based aromatic polyurethane resin
Manufacturers & Suppliers
IMA S.R.L.
manufacturer
Via Segrè, 23, 27036 Mortara, Italia
0384 29.73.11
Emergency Contacts
Emergency Contact
0384/297311
orario d'ufficio / office hours
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| 1-ETHYLPYRROLIDIN-2-ONE EC: 220-250-6 | 2687-91-4 | 12 - 15% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
remove to open air. If respiration is difficult, administer artificial respiration and seek medical advice.
wash with plenty of water; if the irritation persists, seek medical advice.
wash with plenty of water; if the irritation persists, seek medical advice.
seek medical attention. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious person.
Immediate Medical Attention
seek medical advice
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, foam, dry powder, water spray.
Combustion may produce toxic vapours and fumes.
Firefighter Protection
Use full-face positive pressure breathing apparatus and full protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear suitable protective equipment.
Do not allow the liquid to enter watercourses or sewerage systems.
Transfer absorbed material to a suitable drum.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep the vessels in a dry and cool place.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
make sure that the workplace is well aired through effective local aspiration or bad air vent. The product must be used in a closed cycle, in well-aired environments fitted with strong localised aspiration systems (capture speed > 1.5 m/s).
category II (ref. Directive 89/686/EEC and standard EN 374) work gloves, such as those in PVC, neoprene, nitryl or equivalent. The following should be considered when choosing work glove material: degradation, breakage times and permeation. Work glove resistance to preparations should be checked before use, as it can be unpredictable. Gloves' limit depends on the duration of exposure.
Wear hood visor or protective visor together with airtight goggles (ref. standard EN 166)
If the threshold value for one or more of the substances present in the preparation for daily exposure in the workplace or to a fraction established by the company's prevention and protection service is exceeded, wear a mask with an B or universal filter, the class (1, 2 or 3) of which must be chosen according to the limit concentration of use (ref. standard EN 141). The use of breathing protection equipment, such as masks with organic vapour and dust/mist cartridges, is necessary in the absence of technical measures limiting worker exposure. If the substance in question is odourless or its olfactory threshold is higher than the relative exposure limit and in the event of an emergency, or when exposure levels are unknown or the concentration of oxygen in the workplace is less than 17% volume, wear self-contained, open-circuit compressed air breathing apparatus (ref. standard EN 137) or fresh air hose breathing apparatus for use with full face mask, half mask or mouthpiece (ref. standard EN 138).
Wear category II professional long-sleeved overalls and safety footwear (ref. Directive 89/686/CEE and standard EN 344). Wash body with soap and water after removing overalls.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product may react exothermically on contact with strong oxidizing agents or reducers, strong acids or bases.
Oxidizing agents or reducers, strong acids or bases.
In the event of thermal decomposition or fire, vapours potentially dangerous to health may be released.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for IMAPUR HS 03/E?
The signal word is na: r-phrases.
What is the physical form of IMAPUR HS 03/E?
IMAPUR HS 03/E is a viscous liquid appearing as viscous liquid with slightly yellow color. It has characteristic odor.
What is the solubility of IMAPUR HS 03/E?
Insoluble in water
What is IMAPUR HS 03/E used for?
Solvent-based aromatic polyurethane resin
What is the melting point of IMAPUR HS 03/E?
The melting point is Not available and the boiling point is 202 °C.