Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- IMACEL X 15
Regulatory Identifiers
- CAS Number
- 80-51-3 Check regulations →
Identified Uses
Expanding agent
Manufacturers & Suppliers
IMA S.R.L.
manufacturer
Via Segrè, 23, 27036 Mortara (Italia)
0384 29.73.11
Emergency Contacts
Emergency Contact
0384/297311
orario d'ufficio
IT
Emergency Contact
0384/297311
office hours
EN
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| P-P'OXYBIS(BENZENESULFONYLHYDRAZIDE | 80-51-3 | 100% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove to fresh air.
Wash with soap and water for 15 minutes. Seek medical attention if irritation occurs or persists.
Flush with copious amount of water for at least 15 minutes. Seek immediate medical attention.
Do not induce vomiting. Flush mouth with water. Seek immediate medical attention.
Immediate Medical Attention
Seek immediate medical attention.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, foam, dry powder, water spray.
Combustion may produce toxic vapours and fumes.
Firefighter Protection
Use full-face positive pressure breathing apparatus and full protective clothing.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Block the leakage if there is no hazard.
The product must not penetrate the sewer system, surface water, ground water and neighbouring areas.
Use spark proof mechanical tools to collect the leaked product and place in a plastic container.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Shelter from moisture and temperature above 50°C. Keep away from flames and sparks. Do not smoke.
Keep only in the original container.
Do not smoke.
Keep away from flames and sparks.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
make sure that the workplace is well aired through effective local aspiration or bad air vent.
Protect hands with category II (ref. Directive 89/686/EEC and standard EN 374) work gloves, such as those in PVC, neoprene, nitryl or equivalent. The following should be considered when choosing work glove material: degradation, breakage times and permeation. Work glove resistance to preparations should be checked before use, as it can be unpredictable. Gloves' limit depends on the duration of exposure.
Wear protective airtight goggles (ref. standard EN 166).
If the threshold value for one or more of the substances present in the preparation for daily exposure in the workplace or to a fraction established by the company's prevention and protection service is exceeded, wear an FFP3 (ref. standard EN 141) type half mask. The use of breathing protection equipment, such as masks with organic vapour and dust/mist cartridges, is necessary in the absence of technical measures limiting worker exposure. The protection provided by masks is in any case limited. If the substance in question is odourless or its olfactory threshold is higher than the relative exposure limit and in the event of an emergency, or when exposure levels are unknown or the concentration of oxygen in the workplace is less than 17% volume, wear self-contained, open-circuit compressed air breathing apparatus (ref. standard EN 137) or fresh air hose breathing apparatus for use with full face mask, half mask or mouthpiece (ref. standard EN 138).
Wear category II professional long-sleeved overalls and safety footwear (ref. Directive 89/686/CEE and standard EN 344).
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product may react exothermically on contact with strong oxidizing agents or reducers, strong acids or bases.
Oxidizing agents or reducers, strong acids or bases.
In the event of thermal decomposition or fire, vapours potentially dangerous to health may be released.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3226
- Shipping Name
- SELF-REACTIVE SOLID TYPE D (P-P'OXYBIS(BENZENESULFONYLHYDRAZIDE)
- Transport Class
- 4.1
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for IMACEL X 15?
The signal word is danger.
What is the physical form of IMACEL X 15?
IMACEL X 15 is a powder appearing as powder with white color. It has characteristic odor.
What is the solubility of IMACEL X 15?
Soluble in acetone Insoluble in water
What is IMACEL X 15 used for?
Expanding agent
What are the hazard statements for IMACEL X 15?
This substance has 5 hazard statements:
- H242: Heating may cause a fire.
- H315: Causes skin irritation.
- H319: Causes serious eye irritation.
- H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled.
- H335: May cause respiratory irritation.
What is the melting point of IMACEL X 15?
The melting point is Not available and the boiling point is Not available.