NextSDS Logo
Safety Data Sheet EN

ICAPLINK 50B

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
ICAPLINK 50B
Product Code
2811

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Cross Linking Agent.

Manufacturers & Suppliers

I

ICAP-SIRA CHEMICALS AND POLYMERS S.P.A.

manufacturer

Via F.Corridoni 19 20015 Parabiago (MI) Italia

+39 0331 496111

Emergency Contacts

NCEC - National Chemical Emergency Centre

+44 1235 239670

NCEC - National Chemical Emergency Centre

+44 1235 239671

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 2
Eye Irrit. Cat. 2
STOT SE Cat. 3

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.

Precautionary Statements

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P312 Call a POISON CENTER/ doctor/if you feel unwell.
P337 + P313 If eye irritation persists: Get medical advice/attention.
P370 + P378 In case of fire: use dry powder, CO2, foam for extinction. Never use water.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
ethyl acetate EC: 205-500-4 141-78-6 50 - 60% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove casualty to fresh air and keep warm and at rest.

Skin contact

Remove contaminated clothing immediately and dispose off safely. Wash thoroughly the body (shower or bath). After contact with skin, wash immediately with soap and plenty of water.

Eye contact

After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately. Protect uninjured eye.

Symptoms: the product causes considerable irritation which can last for over 24 hours.

Ingestion

Do not under any circumstances induce vomiting. OBTAIN A MEDICAL EXAMINATION IMMEDIATELY.

Immediate Medical Attention

In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

In case of fire: use dry powder, CO2, foam for extinction.

Unsuitable media

In case of fire of insoluble products / immiscible in water, the use of water, increase the risk of propagation of the area of fire.

Specific hazards

Do not inhale explosion and combustion gases. Burning produces heavy smoke. When heated (decomposition) or in case of fire may liberate carbon oxides, gases and vapors which are dangerous to health.

Instructions

Move undamaged containers from immediate hazard area if it can be done safely.

Firefighter Protection

Use suitable breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove persons to safety.

Environmental

Do not allow to enter into soil/subsoil. Do not allow to enter into surface water or drains. Retain contaminated washing water and dispose it.

Cleanup methods

Retain contaminated washing water and dispose it.

Materials: absorbing material, organic, sand

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with skin and eyes, inhalation of vapours and mists. Don't use empty container before they have been cleaned. Before making transfer operations, assure that there aren't any incompatible material residuals in the containers.

Storage

Store at below 20 °C. Keep away from unguarded flame and heat sources. Avoid direct exposure to sunlight. Keep away from unguarded flame, sparks, and heat sources. Avoid direct exposure to sunlight. Avoid accumulating electrostatic charge. Keep away from food, drink and feed.

Hygiene

Contamined clothing should be changed before entering eating areas. Do not eat or drink while working.

Fire prevention

Keep away from unguarded flame and heat sources. Keep away from unguarded flame, sparks, and heat sources. Avoid accumulating electrostatic charge.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Ensure good ventilation to maintain air contaminants below exposure limits. It is advisable to work under vacuum system.

Hands

Use protective gloves that provides comprehensive protection, e.g. Butyl rubber. Protection depends on factors such as: nature of the product, temperature of use, glove thickness and immersion time.

Eyes

Use close fitting safety goggles, don't use eye lens.

Respiratory

Use adequate protective respiratory equipment. Use respiratory protection filters for gas / vapor (Type A / AX brown, ref. Standard EN 141) as a function of the levels of occupational exposure to chemical agents.

Skin/Body

Chemical protection clothing.

Environmental

Prevent spills into public sewers or the immediate environment. Do not empty into drains; dispose of this material and its container at a collection point for hazardous waste and in accordance with local regulations. Refer to applicable national and Community legislation concerning environmental protection, waste water, soil pollution and integrated pollution prevention and control (ex. IPPC). The emissions from ventilation or work process equipment should be checked to ensure compliance with the directives of the binding legislation on environmental protection.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Metal Corrosion
---
Solubility In Fat
---
Boiling Point
77 °C
Bulk Density
---
Flammability
---
Properties Status
---
Crystallisation Point
---
Vapor Pressure
106 mBar (20°C)
Relative Density
0.9
Evaporation Rate
N.D.
Voc Content
---
Odor Threshold
3.60 mg/m3
Lower Explosive Limit
2.2 v/v% (25°C) ethyl acetate
Freezing Point
N.A.
Explosive Limits
---
Ph
N.A.
Dynamic Viscosity
ca. 20 mPas (23°C)
Solidification Point
---
Relative Evaporation Rate
---
Decomposition Temperature
N.D.
Auto Ignition Temperature
427°C (ethyl acetate)
Melting Point
N.A.
Flash Point
1 °C
Upper Explosive Limit
11 v/v% (25°C) ethyl acetate
Appearance
liquid
Colour Intensity
---
Odor
solvent
Molecular Weight
---
Density
---
Cloud Point
---
Colour
---
State Under Standard Conditions
---
Physical State
liquid
Solubility In Water
insoluble
Partition Coefficient
---
Vapor Density
>1
Softening Point
---
Solubility
---
Physical State Data
liquid
Kinematic Viscosity
---
Form
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions

Reactivity

Stable under normal conditions

Avoid

Stable under normal conditions.

Incompatible

Avoid contact with combustible materials. The product could catch fire.

Decomposition

None known. When heated (decomposition) or in case of fire may liberate carbon oxides, gases and vapors which are dangerous to health.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1866
Shipping Name
RESIN SOLUTION
Transport Class
3
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for ICAPLINK 50B?

The signal word is danger.

What is the physical form of ICAPLINK 50B?

ICAPLINK 50B is a liquid appearing as liquid . It has solvent odor.

What is ICAPLINK 50B used for?

Cross Linking Agent.

What are the hazard statements for ICAPLINK 50B?

This substance has 3 hazard statements:

  • H225: Highly flammable liquid and vapour.
  • H319: Causes serious eye irritation.
  • H336: May cause drowsiness or dizziness.

What is the melting point of ICAPLINK 50B?

The melting point is N.A. and the boiling point is 77 °C.