cis-2-Hexene

Move to fresh air. If not breathing, give artificial respiration. Obtain medical attention.

Symptoms: Breathing difficulties. Inhalation of high vapor concentrations may cause symptoms like headache, dizziness, tiredness, nausea and vomiting

Wash off immediately with plenty of water for at least 15 minutes. Obtain medical attention.

Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Obtain medical attention.

Do not induce vomiting. Obtain medical attention.

Water spray. Carbon dioxide (CO₂). Dry chemical. Chemical foam.

Do not use a solid water stream as it may scatter and spread fire.

Flammable. Containers may explode when heated. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back.

Cool closed containers exposed to fire with water spray.

Evacuate personnel to safe areas.

See Section 12 for additional ecological information. Do not let this chemical enter the environment.

Soak up with inert absorbent material.

Materials: sand, silica gel, acid binder, universal binder, sawdust

Ensure adequate ventilation. Avoid contact with skin and eyes. Do not breathe vapors or spray mist. Do not ingest. Remove all sources of ignition. Use explosion-proof equipment. Use only non-sparking tools. Wash hands before breaks and immediately after handling the product. Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharges. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded.

Keep in a dry place. Keep container tightly closed. Keep away from heat and sources of ignition. Flammables area. Keep refrigerated. Keep container tightly closed in a dry and well-ventilated place.

Handle in accordance with good industrial hygiene and safety practice. Keep away from food, drink and animal feeding stuffs. Do not eat, drink or smoke when using this product. Remove and wash contaminated clothing before re-use. Wash hands before breaks and at the end of workday.

Remove all sources of ignition. Use explosion-proof equipment. Use only non-sparking tools. Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharges. To avoid ignition of vapors by static electricity discharge, all metal parts of the equipment must be grounded.

Use explosion-proof electrical/ventilating/lighting/equipment. Ensure that eyewash stations and safety showers are close to the workstation location. Ensure adequate ventilation, especially in confined areas. Wherever possible, engineering control measures such as the isolation or enclosure of the process, the introduction of process or equipment changes to minimise release or contact, and the use of properly designed ventilation systems, should be adopted to control hazardous materials at source

Protective gloves. Glove material: Nitrile rubber, Viton (R). Breakthrough time: See manufacturers recommendations. EU standard: EN 374. Glove comments: (minimum requirement). Inspect gloves before use. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Ensure gloves are suitable for the task: Chemical compatability, Dexterity, Operational conditions, User susceptibility, e.g. sensitisation effects, also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion.

Goggles (European standard - EN 166)

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. To protect the wearer, respiratory protective equipment must be the correct fit and be used and maintained properly. Large scale/emergency use: Use a NIOSH/MSHA or European Standard EN 136 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended Filter type: Organic gases and vapours filter Type A Brown conforming to EN14387. Small scale/Laboratory use: Use a NIOSH/MSHA or European Standard EN 149:2001 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Recommended half mask: Valve filtering: EN405; or; Half mask: EN140; plus filter, EN 141. When RPE is used a face piece Fit Test should be conducted

Wear appropriate protective gloves and clothing to prevent skin exposure

No information available.

Stable under normal conditions.

None known, based on information available

Hazardous polymerization does not occur. No information available.

Keep away from open flames, hot surfaces and sources of ignition. Incompatible products.

Acids. Strong oxidizing agents.

Carbon monoxide (CO). Carbon dioxide (CO2)