Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- 1K Universal Fill in fuer Lsm-Lacke 100 ml
- Product Code
- REZ199
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Paintwork
Manufacturers & Suppliers
Peter Kwasny GmbH
manufacturer
Heilbronner Str. 96, D-74831 Gundelsheim
0049-(0)6269-95-20
Emergency Contacts
Emergency Contact
+49 6269 95 20
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS02
GHS07
Hazard Statements
Precautionary Statements
Still copying SDS data manually?Free
You don't have to. NextSDS reads this SDS and adds the information to your library automatically.
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
If symptoms persist consult doctor.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Cool container whit water
Water with full jet
Can form explosive gas-air mixtures.
Firefighter Protection
Mouth respiratory protective device.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away.
Do not allow product to reach sewage system or any water course. Do not allow to enter sewers/ surface or ground water.
Do not flush with water or aqueous cleansing agents
Related Products
Similar products with comparable safety profiles
SprayMax 1K Fill-in 680071 befüllt mit 100ml des Lackmaterials 1K TOUCH UP SAL DOOSAN KAIROS ORANGE
---
Aerosol 1K Fill-in befüllt mit 200 ml Lack Govaere Brugge
---
Aerosol 2K Fill In + 100ml Lack 2K BHS CAT BLACK
---
Aerosol 2K Fill In + 100ml Lack 2K BHS CAT Yellow
---
Aerosol 2K Fill In + 100ml Lack 2K Epoxy Primer black (SPR64607)
---
Aerosol 1K Fill-in befüllt mit 200 ml Imron Fleet Line Industry NC Topcoat
---
Aerosol 2K Fill In + 100ml Lack 2K Epoxy Primer yellow (SPR64132)
---
Aerosol 2K Fill In for 100ml
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep away from heat and direct sunlight. Ensure good ventilation/exhaustion at the workplace. Take note of emission threshold. Use only in well ventilated areas. Ensure good interior ventilation, especially at floor level. (Fumes are heavier than air).
Store in a cool location. Observe official regulations on storing packagings with pressurized containers. Protect from heat and direct sunlight.
Do not spray onto a naked flame or any incandescent material. Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. Material of gloves: Nitrile rubber, NBR. Penetration time of glove material: Gloves must be changed after every contamination. The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact of a maximum of 15 minutes gloves made of the following materials are suitable: butyl rubber, 0,7mm
Tightly sealed goggles
When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. Half mask with combination filter, class A1P2 minimum, or breathing mask with outer air supply.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Reacts with acids, alkalis and oxidizing agents.
No further relevant information available. No decomposition if used according to specifications.
No further relevant information available.
Possible in traces.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1950
- Shipping Name
- AEROSOLS
- Transport Class
- 2.1
Warning: Gases.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for 1K Universal Fill in fuer Lsm-Lacke 100 ml?
The signal word is warning.
What is the physical form of 1K Universal Fill in fuer Lsm-Lacke 100 ml?
1K Universal Fill in fuer Lsm-Lacke 100 ml is a aerosol appearing as form: aerosol, colour: according to product specification with according to product specification color. It has characteristic odor.
What is 1K Universal Fill in fuer Lsm-Lacke 100 ml used for?
Paintwork
What are the hazard statements for 1K Universal Fill in fuer Lsm-Lacke 100 ml?
This substance has 3 hazard statements:
- H222: Extremely flammable aerosol.
- H319: Causes serious eye irritation.
- H336: May cause drowsiness or dizziness.
What is the melting point of 1K Universal Fill in fuer Lsm-Lacke 100 ml?
The melting point is Undetermined. and the boiling point is Not applicable, as aerosol..