NextSDS Logo
Safety Data Sheet EN

210 LV CLEAR

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
210 LV CLEAR

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Refinish 2K H/S Urethane clearcoat

Uses advised against

Do not use except for purpose

Manufacturers & Suppliers

K

KCC Corporation

manufacturer

100, Je4sandan-ro, Seoun-myeon, Anseong-si, Gyeonggi-do, Korea

82-31-670-7777

K

KCC Corporation

distributor

100, Je4sandan-ro, Seoun-myeon, Anseong-si, Gyeonggi-do, Korea

82-31-670-7777

Emergency Contacts

EU-wide emergency number

112

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 3 H226
Skin Sens. Cat. 1A H317
Muta. Cat. 1B H340
Carc. Cat. 1B H350
STOT RE Cat. 2 H373
Aquatic Chronic Cat. 2 H411

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

GHS09 - Environmental hazard

GHS09

Hazard Statements

H226 Flammable liquid and vapour
H317 May cause an allergic skin reaction
H340 May cause genetic defects
H350 May cause cancer
H373 May cause damage to organs through prolonged or repeated exposure
H411 Toxic to aquatic life with long lasting effects

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P240 Ground and bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/equipment.
P242 Use non-sparking tools.
P243 Take action to prevent static discharges.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection.
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P308 + P313 IF exposed or concerned: Get medical advice/attention.
P314 Get medical advice/attention if you feel unwell.
P321 Specific treatment (if in eyes, wash with plenty of running water; if in contact with skin, wash with plenty of running water; if inhaled, move to fresh air; if ingested, seek medical advice on whether to induce vomiting).
P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
P370 + P378 In case of fire: Use Suitable extinguishing media for extinction(Refer Section SDS 5).
P391 Collect spillage.
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulation

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
1-Chloro-4-(trifluoromethyl)benzene EC: 202-681-1 98-56-6 37 - 44% Yes
n-Butyl acetate EC: 204-658-1 123-86-4 4 - 11% Yes
Styrene, n-butyl methacrylate, n-butyl acrylate, isobornyl acrylate, 2-hydroxyethyl acrylate, acrylic acid copolymer 190524-87-9 4 - 11% No
Acetone EC: 200-662-2 67-64-1 5 - 10% Yes
Solvent naphtha (petroleum), light arom. EC: 265-199-0 64742-95-6 1 - 6% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Take specific treatment if needed. When exposed to large amounts of steam and mist, move to fresh air. Get medical attention immediately. If breathing is stopped or irregular, give artificial respiration and supply oxygen.

Skin contact

Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash contaminated clothing thoroughly before re-using. Get medical attention immediately. Go to the hospital immediately if symptoms (flare, irritate) occur. Remove contaminated clothing, shoes and isolate. Wash thoroughly after handling. Wear gloves when washing the patient, and please avoid contact with contaminated clothing.

Symptoms: flare, irritate

Eye contact

Do not rub your eyes. Immediately flush eyes with plenty of water for at least 15 minutes and call a doctor/physician. Get medical attention immediately.

Ingestion

Please be advised by doctor whether induction of vomit is demanded or not. Rinse your mouth with water immediately. Get medical attention immediately.

Immediate Medical Attention

IF exposed or concerned, get medical attention/advice.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Dry chemical, carbon dioxide, regular foam extinguishing agent, spray

Unsuitable media

Avoid use of water jet for extinguishing

Instructions

Avoid inhalation of materials or combustion by-products. Cool containers with water until well after fire is out. Do not approach the tank surrounded by fire until it is extinguished. In case of conflagration, use automatic fire sprinkler. Major fire may require withdrawal, allowing the object itself to burn. Keep unauthorized personnel out. Move containers from fire area, if you can do without the risk. Notify your local firestation and inform the location of the fire and characteristics hazard. Use appropriate extinguishing measure suitable for surrounding fire. Wear appropriate protective equipment. Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank.

Firefighter Protection

Wear appropriate protective equipment.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Do not direct water at spill or source of leak. Do not touch spilled material. Stop leak if you can do it without risk. Handle the damaged containers or spilled material after wearing appropriate protective equipment. Move container to safe area from the leak area. Must work against the wind, let the upwind people to evacuate. Remove all sources of ignition. Ventilate closed spaces before entering.

Small spill

sand or other non-combustible material, please let use absorption. Wipe off the solvent.

Large spill

Stay upwind and keep out of low areas. Dike for later disposal. Advise emergency services. Inform the relevant authorities.

Environmental

Avoid dispersal of spilt material and runoff and contact with waterways, drains and sewers. Prevent runoff and contact with waterways, drains or sewers.

Cleanup methods

Wipe off the solvent. Spilled material should be treated as a potential risk of waste collected.

Materials: Appropriate container for disposal of spilled material collected.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with incompatible materials. Avoid direct physical contact. Comply with all applicable laws and regulations for handling. Dealing only with a well-ventilated place. Do not handle until all safety precautions have been read and understood. Do not inhale the steam prolonged or repeated. Get the manual before use. Refer to Engineering controls and personal protective equipment. Since emptied containers retain product residue(vapor, liquid, solid) follow all MSDS and label warnings even after container is emptied. Wash thoroughly after handling.

Storage

Avoid direct sunlight. Check regularly for leaks. Do not apply any physical shock to container. Do not apply direct heat. Do not use damaged containers. Keep in the original container. Keep sealed when not in use. No open fire. Please pay attention to incompatibilities materials and conditions to avoid. Save in cool, dry and well ventilated place. Store according to current laws and regulations

Hygiene

Wash thoroughly after handling.

Fire prevention

No open fire. Do not apply direct heat.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Business owner is recommended to maintain below recommended exposure limits for the working place with general exhaust of gas/vapour/mist/fume.

Hands

Wear appropriate glove.

Eyes

Wear primary eye protection such as splash resistant safety goggles with a secondary protection face shield. Provide an emergency eye wash station and quick drench shower in the immediate work area.

Respiratory

Any chemical cartridge respirator with organic vapor cartridge(s). Any chemical cartridge respirator with a full facepiece and organic vapor cartridge(s). Respiratory protection is ranked in order from minimum to maximum. Any air-purifying respirator with a full facepiece and an organic vapor canister. Consider warning properties before use. For Unknown Concentration or Immediately Dangerous to Life or Health: Any supplied-air respirator with full facepiece and operated in a pressure-demand or other positive-pressure mode in combination with a separate escape supply. Any self-contained breathing apparatus with a full facepiece. Under conditions of frequent use or heavy exposure, Respiratory protection may be needed.

Skin/Body

Wear appropriate clothing.

Environmental

Do not let product enter drains. For ecological information refer to section 12.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Boiling Point
---
Odor Threshold
---
Softening Point
---
Lower Explosive Limit
---
Form
---
Auto Ignition Temperature
---
Flammability
---
Crystallisation Point
---
Solubility In Water
---
Molecular Weight
---
State Under Standard Conditions
---
Evaporation Rate
---
Relative Evaporation Rate
---
Relative Density
1.12 ~ 1.16
Physical State Data
liquid
Decomposition Temperature
---
Freezing Point
---
Vapor Pressure
---
Ph
---
Appearance
---
Upper Explosive Limit
---
Solidification Point
---
Kinematic Viscosity
---
Physical State
Liquid
Properties Status
---
Metal Corrosion
---
Cloud Point
---
Flash Point
23.6°C
Colour Intensity
---
Solubility In Fat
---
Melting Point
---
Solubility
---
Vapor Density
---
Explosive Limits
---
Colour
Clear
Bulk Density
---
Dynamic Viscosity
---
Odor
Solvent odor
Partition Coefficient
---
Voc Content
---
Density
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

This material is stable under recommended storage and handling conditions.

Reactivity

Product is stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.

Hazardous reactions

Cylinders exposed to fire may vent and release flammable gas.

Avoid

Avoid contact with incompatible materials and condition. Avoid: Heating, Flames and hot surfaces. Avoid contact with heat, sparks, flame or other ignition sources.

Incompatible

Not available

Decomposition

May emit flammable vapour if involved in fire.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1263
Shipping Name
PAINT (including paint, lacquer, enamel, stain, shellac, varnish, polish, liquid filler and liquid lacquer base)
Transport Class
3
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for 210 LV CLEAR?

The signal word is danger.

What is the physical form of 210 LV CLEAR?

210 LV CLEAR is a liquid with clear color. It has solvent odor odor.

What is 210 LV CLEAR used for?

Refinish 2K H/S Urethane clearcoat

What are the hazard statements for 210 LV CLEAR?

This substance has 6 hazard statements:

  • H226: Flammable liquid and vapour
  • H317: May cause an allergic skin reaction
  • H340: May cause genetic defects
  • H350: May cause cancer
  • H373: May cause damage to organs through prolonged or repeated exposure
  • H411: Toxic to aquatic life with long lasting effects