STRYPEEZE ORIGINAL

If illness occurs, remove patient to fresh air. If breathing is difficult, give oxygen. If breathing has stopped, start artificial respiration.

Remove contaminated clothing. Wash exposed area with soap and water. Launder clothing before reuse.

Flood with plenty of water with eye lids held open for at least 15 minutes.

Immediately give 1 or 2 glasses of water and call physician, hospital emergency room or poison control center for way to induce vomiting. Never give anything by mouth to an unconscious person.

Symptoms: Aspiration of material into lungs can cause chemical pneumotitis which can be fatal.

Water fog, regular foam, carbon dioxide or dry chemical.

Straight water steam will spread fire.

DANGER! EXTREMELY FLAMMABLE. Contact of liquid or vapor with flame or hot surfaces will produce toxic gases and a corrosive residue that will cause deterioration of metal.

Use water spray to cool fire exposed containers and fire affected zone until fire is out and danger of reignition has passed.

Stop spill at source, dike area of spill to keep from spreading and keep out of ground water and streams. Transfer material to metal containers. Absorb remainder with sand, clay, earth, floor absorbent or other material and shovel into containers. Then wash area thoroughly with water and detergent.

Wipe or scrape up any material. Wash area thoroughly with detergent and water; ventilate adequately with good fresh air movement at floor level.

Wear proper protective equipment. Stop spill at source, dike area of spill to keep from spreading and keep out of ground water and streams. Transfer material to metal containers. Absorb remainder with sand, clay, earth, floor absorbent or other material and shovel into containers. Then wash area thoroughly with water and detergent. Ventilate adequately with good fresh air movement at floor level. Do not restart pilot lights or operate electrical devices or other sources of sparks, flames or heat until all vapors (odors) are gone.

Prevent spills from entering storm sewers or drains and contact with soil.

Wipe or scrape up any material. Wash area thoroughly with detergent and water. Transfer material to metal containers. Absorb remainder with sand, clay, earth, floor absorbent or other material and shovel into containers. Shovel up and dispose of at an appropriate waste disposal facility.

Materials: sand, clay, earth, floor absorbent, fire retardant, liquid-absorbing material

Do not breathe material. Keep container closed. Use only with adequate ventilation. Avoid contact with eyes, skin and clothing. Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor and liquid), all hazard precautions given in the data sheet must be observed.

Store in cool place, out of hot sun and below 90F.

Do not store where vapors may come in contact with flames, sparks, or heat. Flammable materials should not be stored in below ground areas that cannot be adequately ventilated at floor level. Do not use cutting or welding torches near full or empty containers.

The vapors are heavier than air and due care must be exercised to prevent them from collecting in low, unventilated areas. Vapors may travel along the floor (even under and around closed doors). Adequate ventilation must be provided with good fresh air movement at floor level by normal cross ventilation or preferably good explosion proof exhaust fans. Limit concentration of any solvent in air to exposure guidelines.

Neoprene, butyl or safety 4H laminate glove.

Chemical goggles or safety glasses with side shield. Plastic glasses may be dissolved by paint removers and other solvents.

At vapor concentration below exposure guidelines none needed. Air-purifying respirators may not be effective and they are not recommended for use with this product. In poorly ventilated areas and in emergencies, an approved self-contained breathing apparatus with a full face piece, operated in pressure demand or other positive pressure mode is advised. (See your safety equipment supplier)

Stable

Will not occur.

Strong oxidizing agents (e.g. nitric acid, permanganates, etc.) strong alkalies (e.g. NaOH ammonia, etc.), strong acids (e.g. HCl, sulfuric, etc.) may react with aluminum.

Carbon dioxide and carbon monoxide, various hydrocarbons.