Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- XTREME CUT 251C
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cutting and Grinding Fluid
Uses advised against
None known.
Manufacturers & Suppliers
QualiChem, Inc
manufacturer
2003 Salem Industrial Drive, Salem, VA 24153
+1-540-375-6700
http://www.qualichem.com
Emergency Contacts
VelocityEHS
+1-800-255-3924
VelocityEHS
+1-813-248-0585
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Distillates, petroleum, hydrotreated | 64742-52-5 | 40 - 60% | No |
| Alkanes,C14-C16,chloro | 1372804-76-6 | 5 - 10% | No |
| Alcohols, C16-18, ethoxylated | 68002-96-0 | 1 - 5% | No |
| Alkylphosphate | 52933-07-0 | 1 - 5% | No |
| Ethanol,2,2'-(methylimino)bis- | 105-59-9 | 1 - 5% | No |
| O-PHENYLPHENOL | 90-43-7 | 1 - 5% | No |
| Propylene glycol | 57-55-6 | 1 - 5% | No |
| Distillates (petroleum), solvent-dewaxed light paraffinic | 64742-56-9 | 0.1 - 1% | No |
| Other components below reportable levels | --- | 20 - 40% | No |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. Call a physician if symptoms develop or persist.
Wash off with soap and water. Get medical attention if irritation develops and persists.
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Symptoms: Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision.
Rinse mouth. Get medical attention if symptoms occur.
Medical Treatment
Provide general supportive measures and treat symptomatically.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
During fire, gases hazardous to health may be formed.
Move containers from fire area if you can do so without risk. Use standard firefighting procedures and consider the hazards of other involved materials.
Firefighter Protection
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers.
Avoid discharge into drains, water courses or onto the ground.
Absorb in vermiculite, dry sand or earth and place into containers.
Materials: vermiculite, dry sand or earth
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes. Avoid prolonged exposure. Provide adequate ventilation. Wear appropriate personal protective equipment. Observe good industrial hygiene practices.
Store in tightly closed container. Store away from incompatible materials (see Section 10 of the SDS).
Observe good industrial hygiene practices.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits.
For prolonged or repeated skin contact use suitable protective gloves.
Wear safety glasses with side shields (or goggles).
In case of insufficient ventilation, wear suitable respiratory equipment.
Wear suitable protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Material is stable under normal conditions.
The product is stable and non-reactive under normal conditions of use, storage and transport.
No dangerous reaction known under conditions of normal use.
Contact with incompatible materials.
Strong oxidizing agents.
No hazardous decomposition products are known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3082
- Shipping Name
- Environmentally hazardous substance, liquid, n.o.s. (Alkanes, C14-17, chloro)
- Transport Class
- 9
- Packing Group
- III
Read safety instructions, SDS and emergency procedures before handling.
Read safety instructions, SDS and emergency procedures before handling.
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for XTREME CUT 251C?
The signal word is warning.
What is the physical form of XTREME CUT 251C?
XTREME CUT 251C is a liquid. appearing as clear to slightly hazy liquid. with amber color. It has mild amine odor.
What is XTREME CUT 251C used for?
Cutting and Grinding Fluid
What are the hazard statements for XTREME CUT 251C?
This substance has 1 hazard statement:
- H319: Causes serious eye irritation.
What is the melting point of XTREME CUT 251C?
The melting point is <40 °F (<4.4 °C) estimated and the boiling point is >212 °F (>100 °C) estimated.