Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- SYLOID® AQ 800
Regulatory Identifiers
- CAS Number
- N/A
- UFI Code
- Not applicable
Identified Uses
SU1 Agriculture, forestry, fishery; SU3 Industrial uses: Uses of substances as such or in preparations at industrial sites; SU5 Manufacture of textiles, leather, fur; SU6b Manufacture of pulp, paper and paper products; SU7 Printing and reproduction of recorded media; SU8 Manufacture of bulk, large scale chemicals; SU10 Formulation [mixing] of preparations and/or re-packaging; SU11 Manufacture of rubber products; SU12 Manufacture of plastics products; SU15 Manufacture of fabricated metal products; SU16 Manufacture of computer, electronic and optical products; SU19 Building and construction work. Various PC (Product categories) and PROC (Process categories) listed.
Uses advised against
No further relevant information available.
Manufacturers & Suppliers
GRACE GmbH
manufacturer
In der Hollerhecke 1, D-67547 Worms, GERMANY
+49 (0)6241 - 403 1549
Emergency Contacts
Emergency Contact
+49 (0)172 7129276
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Preparation of synthetic, amorphous silicon dioxide and organic substances.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| amorphous silicon dioxide, chemically prepared EC: 231-545-4 | 7631-86-9 | 75 - 85% | No |
| Polyethylene low density | 9002-88-4 | 15 - 25% | No |
The mixture fulfils the definition for synthetic polymer microparticles according to EU-REACH. Starting materials of polymers (monomers) are registered under REACH. Polymers themselves are exempted from registration.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air. Seek medical treatment in case of complaints.
Immediately rinse with water. If skin irritation occurs, consult a doctor.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use fire extinguishing methods suitable to surrounding conditions. CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Water with full jet
In case of fire, the following can be released: Carbon monoxide and carbon dioxide
Prevent formation of dust.
Firefighter Protection
Wear personal protective equipment.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective clothing. Keep away from ignition sources.
Damp down dust with water spray. Do not allow to enter sewers, surface or ground water.
Sweep the spill area
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Keep receptacles tightly sealed.
Keep container tightly sealed. Protect from heat and direct sunlight. Store in dry conditions.
Prevent static electric sparks. Keep ignition sources away - Do not smoke.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. Wear gloves for protection against mechanical hazards according to EN 388. Use gloves of stable material (e.g. Nitrile) - if necessary tri-coted to improve the wearability. Check the condition of the gloves prior to each use. Check the permeability prior to each anew use of the glove. Preventive skin protection by use of skin-protecting agents is recommended. After use of gloves apply skin-cleaning agents and skin cosmetics. Material of gloves: Butyl rubber, BR Nitrile rubber, NBR. Recommended thickness of the material: ≥ 0.11 mm. EN 388: Minimum requirements for efficiency level 1 for all groups. Penetration time of glove material: EN 420: Minimum requirements for efficiency level 1 for all groups. For the mixture of chemicals mentioned below the penetration time has to be at least 480 minutes (Permeation according to EN 16523-1:2015: Level 6). For the permanent contact in work areas without heightened risk of injury (e.g. Laboratory) gloves made of the following material are suitable: Butyl rubber, BR Nitrile rubber, NBR. For the permanent contact gloves made of the following materials are suitable: Butyl rubber, BR Nitrile rubber, NBR. Not suitable are gloves made of the following materials: cloth gloves
Safety glasses.
If the WEL value is exceeded. Filter P2
Protective work clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used and stored according to specifications.
No further relevant information available.
Air turbulences of product dust particles will cause an explosive atmosphere.
In case of thermal decomposition caused by smouldering and incomplete combustion toxic fumes may be developed.
No further relevant information available.
Carbon dioxide Carbon monoxide
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for SYLOID® AQ 800?
The signal word is no signal word.
What is the physical form of SYLOID® AQ 800?
SYLOID® AQ 800 is a solid appearing as solid powder white odourless with white color. It has odourless odor.
What is SYLOID® AQ 800 used for?
SU1 Agriculture, forestry, fishery; SU3 Industrial uses: Uses of substances as such or in preparations at industrial sites; SU5 Manufacture of textiles, leather, fur; SU6b Manufacture of pulp, paper and paper products; SU7 Printing and reproduction of recorded media; SU8 Manufacture of bulk, large scale chemicals; SU10 Formulation [mixing] of preparations and/or re-packaging; SU11 Manufacture of rubber products; SU12 Manufacture of plastics products; SU15 Manufacture of fabricated metal products; SU16 Manufacture of computer, electronic and optical products; SU19 Building and construction work. Various PC (Product categories) and PROC (Process categories) listed.
What is the melting point of SYLOID® AQ 800?
The melting point is 60-130 °C (wax) and the boiling point is Not determined.