Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF
- Product Code
- 8.17061
- Chemical Name
- Polysorbate
Regulatory Identifiers
- CAS Number
- 9005-65-6 Check regulations →
- REACH No.
- A registration number is not available for this substance as the substance or its uses are exempted from registration or the annual tonnage does not require a registration.
Identified Uses
Laboratory chemicals, Manufacture of substances
Manufacturers & Suppliers
Millipore
Sigma-Aldrich Chemie GmbH
manufacturer
Eschenstrasse 5, D-82024 TAUFKIRCHEN
+49 (0)89 6513-1130
Emergency Contacts
CHEMTREC Deutschland
0800 181 7059
CHEMTREC weltweit
+49 (0)696 43508409
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
CAS-No. : 9005-65-6
Notes
No components need to be disclosed according to the applicable regulations.
First Aid Measures
Emergency procedures for chemical exposure incidents
After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water Foam Carbon dioxide (CO2) Dry powder
For this substance/mixture no limitations of extinguishing agents are given.
Combustible. Vapours are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating. Development of hazardous combustion gases or vapours possible in the event of fire.
Firefighter Protection
In the event of fire, wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Do not breathe vapours, aerosols. Evacuate the danger area, observe emergency procedures, consult an expert.
Do not let product enter drains.
Take up with liquid-absorbent material (e.g. Chemizorb®). Dispose of properly. Clean up affected area.
Materials: liquid-absorbent material (e.g. Chemizorb®)
Related Products
Similar products with comparable safety profiles
Methyl 4-hydroxybenzoate EMPROVE® ESSENTIAL Ph Eur,BP,JP,NF
CAS: 99-76-3
Thymol cryst., suitable for use as excipient EMPROVE® exp Ph Eur,BP,NF
---
Trehalose dihydrate EMPROVE® EXPERT Ph Eur,ChP,NF,JP Ph Eur,ChP,NF,JP
CAS: 6138-23-4
Succinic acid cryst., EMPROVE® ESSENTIAL ChP, NF, JPE, ACS
CAS: 110-15-6
Ethyl acetate suitable for use as excipient EMPROVE® exp Ph Eur,BP,NF
CAS: 141-78-6
Lactose monohydrate powder EMPROVE® EXPERT Ph Eur,BP,NF,JP
CAS: 10039-26-6
DL-Malic acid EMPROVE® ESSENTIAL Ph Eur,NF,FCC,E 296
CAS: 6915-15-7
Calcium chloride dihydrate EMPROVE® Ph Eur,BP,JP,USP,FCC,E 509
CAS: 10035-04-8
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
For precautions see section 2.2.
Tightly closed. Recommended storage temperature see product label.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Full contact: Material: Nitrile rubber, Minimum layer thickness: 0,4 mm, Break through time: 480 min, Material tested: Camatril® (KCL 730 / Aldrich Z677442, Size M). Splash contact: Material: Nitrile rubber, Minimum layer thickness: 0,11 mm, Break through time: 30 min, Material tested: KCL 741 Dermatril® L. This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Not required; except in case of aerosol formation.
Do not let product enter drains.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The product is chemically stable under standard ambient conditions (room temperature).
Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical.
Violent reactions possible with: Strong oxidizing agents
Strong heating.
No data available
In the event of fire: see section 5
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF?
The signal word is no signal word.
What is the physical form of Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF?
Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF is a liquid with yellow color. It has no data available odor.
What is Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF used for?
Laboratory chemicals, Manufacture of substances
What is the melting point of Tween® 80 (Polysorbate) EMPROVE® ESSENTIAL Ph Eur,JP,NF?
The melting point is No data available and the boiling point is No data available.