Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- ANIOSYME PLA
- Product Code
- 734000
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Cleaning and pre-disinfection of medical devices
Manufacturers & Suppliers
Laboratoires ANIOS
manufacturer
Pavé du Moulin.59260.LILLE - HELLEMMES.FRANCE
+33 (0)3 20 67 67 67
www.anios.com
Emergency Contacts
INRS
+33(0)1 45 42 59 59
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Hazardous substances present on their own: (present in the preparation at a sufficient concentration to give it the toxicological characteristics it would have in a 100% pure state)
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| SODIUM CARBONATE EC: 207-838-8 | 497-19-8 | 25 - 50% | Yes |
| ETHOXYLATED ISOTRIDECANOL | 69011-36-5 | 2.5 - 10% | Yes |
| N,N-DIDECYL-N,N-DIMETHYLAMMONIUM CHLORIDE | 7173-51-5 | 2.5 - 10% | Yes |
| TETRASODIC ETHYLENEDIAMINE TETRAACETATE EC: 200-573-9 | 64-02-8 | 10 - 25% | Yes |
Other substances with occupational exposure limits: No known substance in this category present.
Notes
Full text of risk phrases appearing in section 3: see section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Move the person away from the place of exposure and take him/her outside.
Remove all contaminated or stained clothing immediately. Do not use them again until they have been decontaminated. Rinse immediately and thoroughly with water.
Symptoms: skin irritation
If applicable, remove contact lenses. Wash thoroughly with soft clean water for 15 minutes, holding the eyelids open.
Symptoms: redness, pain or visual impairment
Rinse out the mouth, do not allow to drink, do not induce vomiting. Calm the person down and transfer immediately to hospital or doctor.
Immediate Medical Attention
If there is any redness, pain or visual impairment, consult an ophthalmologist. In the event of skin irritation, seek medical advice. Transfer immediately to hospital or doctor.
Medical Treatment
Show the label to the doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Any extinguishing agents are authorized: foam, sand, carbon dioxide, water, powder.
The product itself does not burn.
Firefighter Protection
Use autonomous insulating breathing apparatus and a full protective suit.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid any contact with the skin and eyes. Consult the safety measures listed under headings 7 and 8.
Prevent any material from entering drains or waterways.
In case of accidental dispersion do not pour any spilled product back into its original container with the intention of re-using it. Collect up dry. Collect up and dispose of in drums, then cover them. Do not mix with any other waste. Wash the contaminated surface thoroughly with water.
Materials: drums
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Follow instructions with regard to conditions of use (read the technical notice). Avoid all contact with skin or eyes. Product for external use - Do not swallow – Do not breathe in the dust. Close the container carefully after use.
Store ONLY in the original package. Keep the container tightly closed. Store between +5°C. and +35°C. in a dry place, away from dampness. Do not use after the expiry date mentioned on the packaging. Keep out of the reach of children
Observe precautions stated on label and also industrial safety regulations
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide eye washes in workshops where the product is constantly handled
When handling this product, wear suitable gloves. Nitrile, latex or ninyle gloves. Gloves must be replaced immediately if they show signs of wear and tear.
Avoid contact with eyes. Wear safety goggles.
Not applicable in normal conditions of use.
For further information, see § 11 of S.D.S. - Toxicological information.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The preparation is stable at the handling and storage conditions recommended per § 7 of the safety data sheet
Avoid any exposure to dampness. Do not mix with other products.
Acids, Copper, brass, iron, galvanized steels. Aluminium and galvanized light alloys.
fumes, carbon dioxide and carbon monoxide, nitrogen oxide.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for ANIOSYME PLA?
The signal word is warning.
What is the physical form of ANIOSYME PLA?
ANIOSYME PLA is a powder or dust appearing as white powder with white color.
What is ANIOSYME PLA used for?
Cleaning and pre-disinfection of medical devices
What are the hazard statements for ANIOSYME PLA?
This substance has 1 hazard statement:
- H319: Possibility of irritation to the eyes.
What is the melting point of ANIOSYME PLA?
The melting point is not specified. and the boiling point is not specified..