NextSDS Logo
Safety Data Sheet EN

Soudal Silicone Remover

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Soudal Silicone Remover
Product Code
102853
Synonyms
Clear - 100mL

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Professional useConsumer useDetergent

Manufacturers & Suppliers

S

Soudal Pty Ltd

national supplier

75 Owen St, Glendenning, NSW 2761, Australia

1300 507 011

Emergency Contacts

Soudal Pty Ltd

1300 507 011

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Eye Irrit. Cat. 2A

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H319 Causes serious eye irritation.

Precautionary Statements

P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P103 Read carefully and follow all instructions.
P264 Wash hands, face and all exposed skin thoroughly after handling.
P280 Wear protective gloves/protective clothing protective clothing, gloves, eye/face protection and suitable respirator.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 If eye irritation persists: Get medical advice/attention.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
hydrocarbons, C11-C14, n-alkanes, isoalkanes, cyclics, < 2% aromatics --- 75 - 100% No
Alcohols, C9-11, ethoxylated 68439-46-3 1 - 5% No
Dipropylene glycol monomethyl ether 34590-94-8 1% No
Ingredients determined to be Non-Hazardous --- --- No
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist.

Skin contact

If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water.

Symptoms: swelling, redness, blistering or irritation

Eye contact

If in eyes, hold eyelids apart and flush the eyes continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a Doctor; or for at least 15 minutes and transport to Doctor or Hospital.

Ingestion

Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice.

Medical Treatment

Treat symptomatically.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

If material is involved in a fire use water fog (or if unavailable fine water spray), alcohol resistant foam, standard foam, dry agent (carbon dioxide, dry chemical powder).

Specific hazards

Combustible material.

Instructions

Fire fighters to wear self-contained breathing apparatus and suitable protective clothing if risk of exposure to vapour or products of combustion or decomposition.

Firefighter Protection

Fire fighters to wear self-contained breathing apparatus and suitable protective clothing if risk of exposure to vapour or products of combustion or decomposition.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Clear area of all unprotected personnel. Slippery when spilt. Avoid accidents, clean up immediately. Work up wind or increase ventilation. Contain - prevent run off into drains and waterways.

Small spill

Wipe up with absorbent (clean rag or paper towels). Collect and seal in properly labelled containers or drums for disposal.

Large spill

Clear area of all unprotected personnel. Slippery when spilt. Avoid accidents, clean up immediately. Wear protective equipment to prevent skin and eye contamination and the inhalation of vapours. Work up wind or increase ventilation. Contain - prevent run off into drains and waterways. Use absorbent (soil, sand or other inert material). Collect and seal in properly labelled containers or drums for disposal. If contamination of crops, sewers or waterways has occurred advise local emergency services.

Environmental

prevent run off into drains and waterways

Cleanup methods

Wipe up with absorbent, use absorbent (soil, sand or other inert material)

Materials: absorbent (clean rag or paper towels), soil, sand or other inert material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid eye contact and repeated or prolonged skin contact. Avoid inhalation of vapour, mist or aerosols.

Storage

Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Keep container standing upright. Keep containers closed when not in use - check regularly for leaks.

Fire prevention

Store away from sources of heat and/or ignition.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Viscous Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Colourless
Colour Intensity
---
Form
Viscous Liquid
Odor
Solvent-like odour
Odor Threshold
---
Ph
N Av
Melting Point
N av
Boiling Point
189 °C
Flash Point
75 °C
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
---
Vapor Pressure
0.1 hPa ; 20 °C
Vapor Density
---
Relative Density
---
Bulk Density
---
Density
0.8 g/cm³ (20°C)
Flammability
---
Upper Explosive Limit
14
Lower Explosive Limit
0.6
Explosive Limits
---
Auto Ignition Temperature
207 °C
Decomposition Temperature
N av
Solubility
---
Partition Coefficient
---
Solubility In Water
Insoluble
Solubility In Fat
---
Molecular Weight
---
Voc Content
95.2 %
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
900 mm²/s (40°C)
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

This material is thermally stable when stored and used as directed.

Hazardous reactions

No known hazardous reactions.

Avoid

Elevated temperatures and sources of ignition.

Incompatible

Oxidising agents.

Decomposition

Oxides of carbon and nitrogen, smoke and other toxic fumes.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What other names is Soudal Silicone Remover known by?

Soudal Silicone Remover is also known as: Clear - 100mL

What is the hazard signal word for Soudal Silicone Remover?

The signal word is warning.

What is the physical form of Soudal Silicone Remover?

Soudal Silicone Remover is a viscous liquid with colourless color. It has solvent-like odour odor.

What is Soudal Silicone Remover used for?

Professional useConsumer useDetergent

What are the hazard statements for Soudal Silicone Remover?

This substance has 1 hazard statement:

  • H319: Causes serious eye irritation.

What is the melting point of Soudal Silicone Remover?

The melting point is N av and the boiling point is 189 °C.