NextSDS Logo
Safety Data Sheet EN

CELLCLEAN AUTO

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
CELLCLEAN AUTO

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Diagnostic testing

Uses advised against

No further relevant information available.

Manufacturers & Suppliers

S

SYSMEX AMERICA, Inc

manufacturer

577 Aptakisic Road, Lincolnshire, IL 60069 USA

847-996-4500, 1-800-379-7639

Emergency Contacts

ChemTel Inc.

(800)255-3924

ChemTel Inc.

+1 (813)248-0585

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Skin Corr. Cat. 1C H314

GHS Pictograms

GHS05 - Corrosive

GHS05

Hazard Statements

H314 Causes severe skin burns and eye damage.

Precautionary Statements

P260 Do not breathe mist/vapours/spray.
P264 Wash thoroughly after handling.
P280 Wear protective gloves and eye protection.
P301 + P330 + P331 If swallowed: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305 + P351 + P338 If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

Mixture of the substances listed below with nonhazardous additions.

Chemical Name CAS Number Concentration Hazardous
sodium hypochlorite EC: 231-668-3 7681-52-9 2.5 - 10% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Supply fresh air; consult doctor in case of complaints. Provide oxygen treatment if affected person has difficulty breathing.

Symptoms: Coughing, Breathing difficulty, Danger of impaired breathing, Caustic effect on mucous membranes.

Skin contact

Immediately rinse with water. If skin irritation continues, consult a doctor. Seek immediate medical help for blistering or open wounds.

Symptoms: Caustic effect on skin.

Eye contact

Protect unharmed eye. Remove contact lenses if worn. Rinse opened eye for several minutes under running water. Then consult a doctor.

Symptoms: Causes serious eye damage.

Ingestion

Rinse out mouth and then drink plenty of water. Do not induce vomiting; immediately call for medical help.

Symptoms: Gastric or intestinal disorders when ingested, Nausea in case of ingestion, Danger of gastric perforation, Caustic effect on mucous membranes.

Immediate Medical Attention

Seek immediate medical help for blistering or open wounds. Immediately call for medical help if swallowed.

Medical Treatment

If necessary oxygen respiration treatment.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use fire fighting measures that suit the environment.

Unsuitable media

None.

Specific hazards

During heating or in case of fire poisonous gases are produced.

Firefighter Protection

Wear self-contained respiratory protective device. Wear fully protective suit.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Keep unprotected persons away.

Large spill

For large spills, use respiratory protective device against the effects of fumes/dust/aerosol.

Environmental

Do not allow to enter sewers/ surface or ground water.

Cleanup methods

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Send for recovery or disposal in suitable receptacles.

Materials: sand, diatomite, acid binders, universal binders, sawdust

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Prevent formation of aerosols. Use only in well ventilated areas. Avoid splashes or spray in enclosed areas.

Storage

Store in cool, dry conditions in well sealed receptacles. Keep receptacle tightly sealed.

Fire prevention

No special measures required.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Hands

Protective gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. For the permanent contact gloves made of the following materials are suitable: PVC gloves, Rubber gloves

Eyes

Contact lenses should not be worn. Safety glasses

Respiratory

Use suitable respiratory protective device when high concentrations are present. Use suitable respiratory protective device when aerosol or mist is formed. For spills, respiratory protection may be advisable.

Skin/Body

Alkaline resistant protective clothing

Environmental

No further relevant information available.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Partition Coefficient
Not determined.
Properties Status
---
Explosive Limits
---
Solidification Point
---
Melting Point
Undetermined.
Flammability
Not applicable.
Cloud Point
---
Auto Ignition Temperature
Not determined.
Boiling Point
Undetermined.
State Under Standard Conditions
---
Solubility In Water
Fully miscible.
Bulk Density
---
Kinematic Viscosity
Not determined.
Lower Explosive Limit
Not determined.
Voc Content
---
Colour
Light yellow
Flash Point
Not applicable.
Appearance
---
Relative Evaporation Rate
---
Metal Corrosion
---
Odor Threshold
Not determined.
Vapor Density
Not determined.
Density
1.07 g/cm³ (8.929 lbs/gal)
Freezing Point
---
Molecular Weight
---
Form
Liquid
Odor
Pungent
Vapor Pressure
Not determined.
Physical State Data
liquid
Decomposition Temperature
Not determined.
Crystallisation Point
---
Colour Intensity
---
Solubility In Fat
---
Solubility
---
Upper Explosive Limit
Not determined.
Softening Point
---
Ph
> 12
Dynamic Viscosity
Not determined.
Relative Density
Not determined.
Physical State
liquid
Evaporation Rate
Not determined.
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if used and stored according to specifications.

Reactivity

Corrosive action on metals.

Hazardous reactions

Contact with acids releases toxic gases. Reacts with many consumer products, releasing chlorine or chlorine oxide gas. Reacts with strong oxidizing agents.

Avoid

To avoid thermal decomposition do not overheat.

Incompatible

Acids, many consumer products, strong oxidizing agents, metals.

Decomposition

Toxic gases (chlorine or chlorine oxide gas), toxic fumes.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1791
Shipping Name
Hypochlorite solutions
Transport Class
8
Packing Group
III
ADR

Warning: Corrosive substances

IMDG

Warning: Corrosive substances

IATA

Warning: Corrosive substances

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for CELLCLEAN AUTO?

The signal word is danger.

What is the physical form of CELLCLEAN AUTO?

CELLCLEAN AUTO is a liquid with light yellow color. It has pungent odor.

What is CELLCLEAN AUTO used for?

Diagnostic testing

What are the hazard statements for CELLCLEAN AUTO?

This substance has 1 hazard statement:

  • H314: Causes severe skin burns and eye damage.

What is the melting point of CELLCLEAN AUTO?

The melting point is Undetermined. and the boiling point is Undetermined..