Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- MOLDCOTE 13
- Product Code
- 1073
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
FOSECO (F.S.) Ltd
manufacturer
Tamworth Stalls B78 3TL
01827-288699
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
GHS02
GHS06
Hazard Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove from exposure. Keep warm and at rest. If breathing stops or shows signs of failing, give artificial respiration. Obtain medical attention urgently.
Wash skin with water. Remove contaminated clothing as washing proceeds. Continue washing for at least 10 minutes. Obtain medical attention urgently. Contaminated clothing should be washed or dry-cleaned before re-use.
Immediately flood the eye with plenty of water for at least 15 minutes, holding the eye open. Obtain medical attention urgently.
Do not induce vomiting. Never administer anything by mouth if a victim is losing consciousness, is unconscious or is convulsing. Wash out mouth with water. Have victim drink 1-3 glasses of water to dilute stomach contents. Obtain medical attention urgently. If breathing stops or shows signs of failing, apply artificial respiration.
Immediate Medical Attention
Obtain medical attention urgently. Immediate specialist medical attention is recommended in all cases of over-exposure. In case of eye contact immediate referral for ophthalmological opinion is advised.
Medical Treatment
Monitor for effects on CNS function; support and treat.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. Keep containers and surroundings cool with water spray. Disperse accumulating vapour with water spray. Water spray should be used to absorb heat and keep exposed material free from fire damage.
Do not use water jet.
This product may give rise to hazardous fumes in a fire. Moderate to severe explosive hazard in confined spaces. Containers may explode in heat of fire. Run off to sewer may cause fire or explosion hazard. May form explosive mixtures with air. Dangerous when exposed to heat or flame. Vapours can travel a considerable distance to a source of ignition and flashback. Flashback can occur if air temperature exceeds flash point.
Keep containers and surroundings cool with water spray. Disperse accumulating vapour with water spray.
Firefighter Protection
Wear full protective clothing and self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Evacuate area. Eliminate all sources of ignition. Beware of vapours accumulating to form explosive concentrations. Vapours can accumulate in low areas. Lasers inside confined spaces may cause suffocation. Wear appropriate protective clothing. Wear respiratory protection. Wear fireproof clothing.
Try to prevent the material from entering drains or water courses. Advise Authorities if spillage has entered water course or sewer or has contaminated soil or vegetation.
Transfer into suitable containers for recovery or disposal. Disperse vapour with water spray. Finally flush area with plenty of water.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Adequate ventilation should be provided if there is risk of vapour build-up. Use local exhaust ventilation. Avoid inhaling vapour. Avoid contact with eyes, skin and clothing.
cool, well ventilated, out of direct sunlight, away from incompatible materials, isolated, unheated. Keep container tightly closed when not in use.
Emergency shower and eye wash facilities should be readily available.
Store away from sources of heat or ignition. Storage and transfer equipment should be adequately earthed and bonded to prevent the accumulation of static charges.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Decomposes readily on heating.
Reacts violently with: oxidising agents, nitric acid, many chemicals.
High temperatures. Exposure to direct sunlight. Static discharge. Pressure.
Strong oxidisers. Nitric acid.
Combustion will generate: acid smells and irritating fumes, toxic fumes, smoke, possibly thick and choking, resulting in zero visibility.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 1993
- Shipping Name
- Flammable liquid, n.o.s. Contains Naptha, Solvent and White Spirit
- Transport Class
- 3
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for MOLDCOTE 13?
The signal word is danger.
What is the physical form of MOLDCOTE 13?
MOLDCOTE 13 is a liquid. with silver. color. It has characteristic. odor.
What are the hazard statements for MOLDCOTE 13?
This substance has 3 hazard statements:
- H220: Flammable.
- H331: Harmful by inhalation and if swallowed.
- Mild by pollutant.