NextSDS Logo
Safety Data Sheet EN

FLOWBUILD COVE F PART A

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
FLOWBUILD COVE F PART A

Regulatory Identifiers

CAS Number
N/A
UFI Code
FGH0-A025-T003-UWV9

Identified Uses

Manual activities involving hand contact. Widespread use leading to inclusion into/ onto article (indoor). For use by appropriately trained applicators. Roller application or brushing. Low energy spreading of coatings. Component of multicomponent coatings - Industrial and professional use.

Uses advised against

Home DIY applications, because of the health hazards and training required. others than recommended

Manufacturers & Suppliers

C

Construction Products Group

Tremco CPG Poland Sp. z o. o. logo

Tremco CPG Poland Sp. z o. o.

manufacturer

Ul. Marywilska 34, 03-228 Warszawa, Polska

+48 22 879 8907

http://www.flowcrete.com.pl/

Emergency Contacts

CHEMTREC

+1 703 5273887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Skin Irrit. Cat. 2 H315
Skin Sens. Cat. 1 H317
Aquatic Chronic Cat. 3 H412

GHS Pictograms

GHS07 - Health hazard

GHS07

Hazard Statements

H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.

Precautionary Statements

P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/ face protection.
P501 Dispose of contents/container to waste treatment/disposal facility in accordance with local, state, and federal regulations.
IF ON SKIN: Wash with plenty of soap and water.
If skin irritation or rash occurs: Get medical advice/attention.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
bis[4-(2,3-epoxypropoxy) phenyl]propane EC: 216-823-5 1675-54-3 2.5 - 10% Yes
henyleneoxymethylene)]bis (oxirane) and 2,2'-[methylenebis EC: 701-263-0 --- 1 - 2.5% Yes
Oxirane, mono[(C12-14-alkyloxy)methyl] derivs. EC: 271-846-8 68609-97-2 1 - 2.5% Yes
Quaternary ammonium compounds, benzyl-C14-18-alkyldimethyl, chlorides 68390-98-7 0.1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Keep respiratory tract clear. Remove person to fresh air. If signs/symptoms continue, get medical attention.

Skin contact

Use a mild soap if available. Wash off immediately with soap and plenty of water while removing all contaminated clothes and shoes. If skin irritation persists, call a physician.

Eye contact

Keep eye wide open while rinsing. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses. If eye irritation persists, consult a specialist.

Ingestion

Gently wipe or rinse the inside of the mouth with water. Do not induce vomiting without medical advice. Never give anything by mouth to an unconscious person. If swallowed, seek medical advice immediately and show this container or label.

Immediate Medical Attention

If signs/symptoms continue, get medical attention. If skin irritation persists, call a physician. If eye irritation persists, consult a specialist. If swallowed, seek medical advice immediately.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Carbon Dioxide, Dry Chemical, Foam, Water Fog

Unsuitable media

Alcohol, Alcohol based solutions, any other media not listed above.

Specific hazards

In case of fire hazardous decomposition products may be produced such as: Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), dense black smoke.

Instructions

Keep containers and surroundings cool with water spray.

Firefighter Protection

In the event of fire, wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Keep people away from and upwind of spill/leak.

Environmental

Do not allow material to contaminate ground water system. Prevent product from entering drains. May cause long-term adverse effects in the aquatic environment.

Cleanup methods

soak up with non-combustible absorbent material and transfer to a container for disposal

Materials: non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Wear personal protective equipment. Use only in well-ventilated areas. Do not breathe vapours or spray mist. Avoid contact with skin and eyes.

Storage

Keep at temperatures between 5 and 25 °C. Do not freeze. Store at room temperature in the original container. Keep locked up or in an area accessible only to qualified or authorised persons. Keep container closed when not in use. Store in a dry, well ventilated place away from sources of heat, ignition and direct sunlight.

Hygiene

Handle in accordance with good industrial hygiene and safety practice. Keep working clothes separately. Keep away from food, drink and animal feedingstuffs. When using, do not eat, drink or smoke. Wash hands and face before breaks and immediately after handling the product.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

As a rule, at least 5 air changes per hour are recommended at the workplace. Ensure adequate ventilation, especially in confined areas.

Hands

Impervious gloves. Chemical resistant gloves made of butyl rubber or nitrile rubber category III according to EN 374. Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact).

Eyes

Eye wash bottle with pure water. Tightly fitting safety goggles. If splashes are likely to occur, wear: Face-shield, tightly fitting safety goggles (EN 166).

Respiratory

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators. Wear a positive-pressure supplied-air respirator. In case of insufficient ventilation and where workplace exposure limits may be exceeded, wear suitable respiratory equipment. Respirator with filter for organic vapor. Recommended Filter type: A2, EN 136/140/145/143/149

Skin/Body

Long sleeved clothing.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
No Information
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Not determined
Colour Intensity
---
Form
---
Odor
No Information
Odor Threshold
Not determined
Ph
Not determined
Melting Point
Not determined
Boiling Point
N.D. - N.D.
Flash Point
Not measured
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not determined
Vapor Pressure
Not determined
Vapor Density
---
Relative Density
0.120
Bulk Density
---
Density
Not determined
Flammability
Not determined
Upper Explosive Limit
Not determined
Lower Explosive Limit
Not determined
Explosive Limits
---
Auto Ignition Temperature
Not determined
Decomposition Temperature
Not determined
Solubility
---
Partition Coefficient
Not determined
Solubility In Water
Not determined
Solubility In Fat
---
Molecular Weight
---
Voc Content
< 500 (A+B) g/l
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
Not determined
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if stored and applied as directed. Stable under normal conditions.

Reactivity

No reactivity hazards known under normal storage and use conditions.

Hazardous reactions

Hazardous polymerisation does not occur.

Avoid

Do not freeze.

Incompatible

oxidising agents, strongly alkaline and strongly acid materials, Strong oxidizing agents, Copper alloys, Copper, radical-forming starting agents, peroxides, reactive metals, Halogenated hydrocarbons.

Decomposition

In case of fire hazardous decomposition products may be produced such as: Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), dense black smoke.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for FLOWBUILD COVE F PART A?

The signal word is warning.

What is the physical form of FLOWBUILD COVE F PART A?

FLOWBUILD COVE F PART A is a no information with not determined color. It has no information odor.

What is FLOWBUILD COVE F PART A used for?

Manual activities involving hand contact. Widespread use leading to inclusion into/ onto article (indoor). For use by appropriately trained applicators. Roller application or brushing. Low energy spreading of coatings. Component of multicomponent coatings - Industrial and professional use.

What are the hazard statements for FLOWBUILD COVE F PART A?

This substance has 3 hazard statements:

  • H315: Causes skin irritation.
  • H317: May cause an allergic skin reaction.
  • H412: Harmful to aquatic life with long lasting effects.

What is the melting point of FLOWBUILD COVE F PART A?

The melting point is Not determined and the boiling point is N.D. - N.D..