NextSDS Logo
Safety Data Sheet EN

Flowprime LW Part B

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Flowprime LW Part B

Regulatory Identifiers

CAS Number
N/A
UFI Code
R6D2-70Q0-K007-CYQ7

Identified Uses

Component of multicomponent coatings - Professional use only. Coatings and paints, thinners, paint removers. Manual activities involving hand contact. Widespread use leading to inclusion into/onto article (indoor). Widespread use leading to inclusion into/onto article (outdoor). For use by appropriately trained applicators. Roller application or brushing.

Uses advised against

Home DIY applications. Spray application, because of the additional hazards. others than recommended

Manufacturers & Suppliers

Tremco CPG Poland Sp. z o. o. logo

Tremco CPG Poland Sp. z o. o.

manufacturer

Ul. Marywilska 34, 03-228 Warszawa, Polska

+48 22 879 8907

http://www.flowcrete.com.pl/

Emergency Contacts

CHEMTREC

+1 703 5273887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4 H302
Skin Corr. Cat. 1B H314
Skin Sens. Cat. 1 H317
Repr. Cat. 2
Aquatic Chronic Cat. 3 H412

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H302 Harmful if swallowed.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H361d Suspected of damaging the unborn child.
H412 Harmful to aquatic life with long lasting effects.

Precautionary Statements

P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P284 Wear respiratory protection.
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do so. Continue rinsing.
IF exposed or concerned: Get medical advice/attention.
If skin irritation or rash occurs: Get medical advice/attention.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Benzyl alcohol EC: 202-859-9 100-51-6 25 - 50% Yes
4,4'-Isopropylidenediphenol, oligomeric reaction products with 1-chloro-2,3-epoxypropane, reaction products with 3-aminomethyl-3,5,5-trimethylcyclohexylamine. EC: 500-101-4 38294-64-3 25 - 50% Yes
3-Aminomethyl-3,5,5-trimethylcyclohexylamine EC: 220-666-8 2855-13-2 10 - 25% Yes
m-Phenylenebis(methylamine) EC: 216-032-5 1477-55-0 2.5 - 10% Yes
Salicylic acid EC: 200-712-3 69-72-7 2.5 - 10% Yes
Reaction products of di-, tri- and tetra-propoxylated propane-1,2-diol with ammonia. EC: 618-561-0 9046-10-0 2.5 - 10% Yes

The text for CLP Hazard Statements shown above (if any) is given in Section 16.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person to fresh air. If signs/symptoms continue, get medical attention.

Symptoms: Harmful by inhalation

Skin contact

Use a mild soap if available. Do not use solvent or thinners to clean skin. Wash off immediately with soap and plenty of water while removing all contaminated clothes and shoes.

Symptoms: Corrosion of the skin.

Eye contact

Keep eye wide open while rinsing. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses.

Symptoms: Causes serious eye damage.

Ingestion

Gently wipe or rinse the inside of the mouth with water. If conscious, drink plenty of water. Never give anything by mouth to an unconscious person. If swallowed, seek medical advice immediately and show this container or label. If swallowed, DO NOT induce vomiting unless directed to do so by medical personnel.

Symptoms: Harmful if swallowed.

Immediate Medical Attention

Consult a physician. Immediate medical treatment is necessary as untreated wounds from corrosion of the skin heal slowly and with difficulty. Immediate medical attention is required for eye contact.

Medical Treatment

Consult a physician. Immediate medical treatment is necessary as untreated wounds from corrosion of the skin heal slowly and with difficulty.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Carbon Dioxide, Dry Chemical, Foam

Unsuitable media

Do not use a solid water stream as it may scatter and spread fire. Alcohol, Alcohol based solutions, any other media not listed above.

Specific hazards

In case of fire hazardous decomposition products may be produced such as; Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), dense black smoke.

Instructions

Keep containers and surroundings cool with water spray.

Firefighter Protection

In the event of fire, wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Avoid contact with skin, eyes and clothing. Ensure adequate ventilation. Keep people away from and upwind of spill/leak.

Environmental

Discharge into the environment must be avoided.

Cleanup methods

soak up with non-combustible absorbent material and transfer to a container for disposal

Materials: non-combustible absorbent material (e.g. sand, earth, diatomaceous earth, vermiculite)

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Wear personal protective equipment. Do not breathe vapours or spray mist. Avoid contact with skin and eyes. People handling epoxy products must have received special training according to guidelines from the National Occupational Health and Safety Board. In the case of sensitisation to any of the ingredients, it is inadvisable to work with the product.

Storage

Keep out of the reach of children. Keep at temperatures between 15 and 30 °C. Store in original container. Keep container tightly closed in a dry and well-ventilated place. Keep container closed when not in use.

Hygiene

Handle in accordance with good industrial hygiene and safety practice. Keep working clothes separately. Keep away from food, drink and animal feedingstuffs. Wash hands before breaks and at the end of workday. When using, do not eat, drink or smoke.

Fire prevention

Avoid contact with sources of heat.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

Ensure adequate ventilation, especially in confined areas.

Hands

Use chemical resistant gloves (EN 374): Nitrile rubber; thickness >=0.5 mm; breakthrough time >= 480 min. Gloves should be discarded and replaced if there is any indication of degradation or chemical breakthrough. Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact). Be aware that in daily use the durability of a chemical resistant protective glove can be notably shorter than the break through time measured according to EN 374, due to the numerous outside influences (e.g. temperature).

Eyes

Eye wash bottle with pure water. Face-shield. Safety glasses with side-shields conforming to EN 166.

Respiratory

When mixing or applying this product, the installation area should be well ventilated, either naturally or via mechanical ventilation to prevent vapor accumulation. In case of insufficient ventilation or work in confined spaces, workers should wear a NIOSH or CE approved half face air purifying respirator (APR) equipped with organic vapor cartridges. In case of insufficient ventilation wear suitable respiratory equipment.

Skin/Body

Long sleeved clothing.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
---
Colour
Light yellow
Colour Intensity
---
Form
---
Odor
Amine like
Odor Threshold
Not determined
Ph
Not determined
Melting Point
Not determined
Boiling Point
>190°C - N.D.
Flash Point
Not measured
Freezing Point
---
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not determined
Vapor Pressure
Not determined
Vapor Density
---
Relative Density
ca. 1.02
Bulk Density
---
Density
0.120 g/cm3
Flammability
Not determined
Upper Explosive Limit
Not determined
Lower Explosive Limit
Not determined
Explosive Limits
---
Auto Ignition Temperature
Not determined
Decomposition Temperature
Not determined
Solubility
---
Partition Coefficient
Not determined
Solubility In Water
Miscible
Solubility In Fat
---
Molecular Weight
---
Voc Content
<175 g/l
Metal Corrosion
---
Dynamic Viscosity
---
Kinematic Viscosity
Not determined
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

No decomposition if stored and applied as directed.

Reactivity

No reactivity hazards known under recommended storage and use conditions.

Hazardous reactions

Exothermic reaction with strong acids.

Avoid

Avoid temperatures above 40 °C, direct sunlight and contact with sources of heat. Do not freeze.

Incompatible

Acids. Oxidizing agents.

Decomposition

Carbon dioxide (CO2), carbon monoxide (CO), oxides of nitrogen (NOx), dense black smoke.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN2735
Shipping Name
Amines, liquid, corrosive, N.O.S., (m-Xylenediamine, Isophoronediamine)
Transport Class
8
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Flowprime LW Part B?

The signal word is danger.

What is the physical form of Flowprime LW Part B?

Flowprime LW Part B is a liquid with light yellow color. It has amine like odor.

What is Flowprime LW Part B used for?

Component of multicomponent coatings - Professional use only. Coatings and paints, thinners, paint removers. Manual activities involving hand contact. Widespread use leading to inclusion into/onto article (indoor). Widespread use leading to inclusion into/onto article (outdoor). For use by appropriately trained applicators. Roller application or brushing.

What are the hazard statements for Flowprime LW Part B?

This substance has 5 hazard statements:

  • H302: Harmful if swallowed.
  • H314: Causes severe skin burns and eye damage.
  • H317: May cause an allergic skin reaction.
  • H361d: Suspected of damaging the unborn child.
  • H412: Harmful to aquatic life with long lasting effects.

What is the melting point of Flowprime LW Part B?

The melting point is Not determined and the boiling point is >190°C - N.D..