Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Düsofix anti-spatter paste
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
intended for professional use only! Processing aid
Manufacturers & Suppliers
Alexander BINZEL Schweißtechnik GmbH & Co.KG
manufacturer
Postfach 10 01 53 / D-35331 Giessen
+49 (0) 6408 / 59-0
Emergency Contacts
Giftinformationszentrum der Länder Rheinland-Pfalz und Hessen
+49 (0)6131 / 19 24 0
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture: consisting of the following components.
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
Supply fresh air; consult doctor in case of complaints.
Immediately remove any clothing soiled by the product. Immediately wash with water and soap and rinse thoroughly.
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. Protect unharmed eye.
Immediate Medical Attention
Seek medical treatment in case of complaints. If symptoms persist consult doctor.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. Use fire extinguishing methods suitable to surrounding conditions.
Formation of toxic gases is possible during heating or in case of fire.
Firefighter Protection
Do not inhale explosion gases or combustion gases.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Wear protective equipment. Keep unprotected persons away. Ensure adequate ventilation.
Prevent from spreading (e.g. by damming-in or oil barriers).
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Do not flush with water or aqueous cleansing agents.
Materials: sand, diatomite, acid binders, universal binders, sawdust
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Store in cool, dry place in tightly closed receptacles. Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Store in cool, dry place in tightly closed receptacles.
No special measures required.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Protective gloves. Check protective gloves prior to each use for their proper condition. Only use chemical-protective gloves with CE-labelling of category III. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. After use of gloves apply skin-cleaning agents and skin cosmetics. Recommended materials: Butyl rubber, BR Recommended thickness of the material: ≥ 0.5 mm The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. The determined penetration times according to EN 374 part III are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended. As protection from splashes gloves made of the following materials are suitable: Nitrile rubber, NBR Recommended thickness of the material: ≥ 0.1 mm Penetration time (min.): <10
Tightly sealed goggles. Protective goggles and facial protection - Classification according to EN 166
When used properly and under normal conditions, breathing protection is not required. Use suitable respiratory protective device in case of insufficient ventilation. Filter A/P2
Protective work clothing. Impervious protective clothing.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No decomposition if used according to specifications.
No further relevant information available.
No dangerous reactions known.
No further relevant information available.
No further relevant information available.
No dangerous decomposition products known.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Düsofix anti-spatter paste?
The signal word is no signal word.
What is the physical form of Düsofix anti-spatter paste?
Düsofix anti-spatter paste is a pasty appearing as pasty with yellow color. It has nearly odourless odor.
What is Düsofix anti-spatter paste used for?
intended for professional use only! Processing aid
What is the melting point of Düsofix anti-spatter paste?
The melting point is Undetermined. and the boiling point is 516 °C.