Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Anti-spatter fluid
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Alexander BINZEL Schweißtechnik GmbH & Co.KG
manufacturer
Postfach 10 01 53 / D-35331 Giessen
+49 (0) 6408 / 59-0
Binzel Pty. Ltd.
distributor
42 Hinkler Rd, Mordialloc, Victoria, 3195, Australia
+61 (0)39580 6500
Emergency Contacts
Giftinformationszentrum der Länder Rheinland-Pfalz und Hessen
+49 (0)6131 / 19 24 0
Poison Information Center
131 126
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Mixture of substances listed below with nonhazardous additions.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| White mineral oil, petroleum | 8042-47-5 | 12.5 - 25% | Yes |
For the wording of the listed hazard phrases refer to section 16.
First Aid Measures
Emergency procedures for chemical exposure incidents
In case of unconsciousness place patient stably in side position for transportation. Supply fresh air; consult doctor in case of complaints.
Immediately wash with water and soap and rinse thoroughly. Seek medical treatment in case of complaints.
Seek medical treatment. Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. Protect unharmed eye.
If symptoms persist consult doctor.
Immediate Medical Attention
No further relevant information available.
Medical Treatment
No further relevant information available.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
The data for this section has not been processed yet.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
The data for this section has not been processed yet.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
The data for this section has not been processed yet.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
No further data; see item 7.
Protective gloves. Check protective gloves prior to each use for their proper condition. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. After use of gloves apply skin-cleaning agents and skin cosmetics. Material: Nitrile rubber, NBR. Recommended thickness: ≥ 0.1 mm. Penetration time: The determined penetration times according to EN 16523-1:2015 are not performed under practical conditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time, is recommended.
Tightly sealed goggles. Protective goggles and facial protection - Classification according to EN 166
When used properly and under normal conditions, breathing protection is not required.
protective clothing (EN 13034)
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
The data for this section has not been processed yet.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Anti-spatter fluid?
The signal word is no signal word.
What is the physical form of Anti-spatter fluid?
Anti-spatter fluid is a fluid with yellowish color. It has nearly odourless odor.
What is the melting point of Anti-spatter fluid?
The melting point is Undetermined. and the boiling point is 240 C.