Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Radolid Korrex EP 7010
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Lubricants, greases and release agents ( Fat ).
Manufacturers & Suppliers
Radolid Thiel GmbH
manufacturer
Lösenbacher Landstraße 166, 58509 Lüdenscheid
+49 (0)2351/979494
Emergency Contacts
Product safety department
+49 (0)2351/979494
CET 07:00 – 16:15
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
Base oil with thickener and additives.
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Fabrikationsöl, Hochraffiniertes Mineralöl EC: 265-166-0 | 64742-62-7 | 25 - 50% | No |
| DI-TERT-DODECYL POLYSULFIDE EC: 270-335-7 | 68425-15-0 | 1 - 10% | Yes |
Highly refined mineral oil (IP 346 DMSO extract < 3%).
First Aid Measures
Emergency procedures for chemical exposure incidents
No special measures are necessary. Provide fresh air. When in doubt or if symptoms are observed, get medical advice.
After contact with skin, first remove product with a dry cloth and then wash the skin with plenty of water.
Remove contact lenses, if present and easy to do. Continue rinsing. Wash with plenty of water. Call a physician immediately.
Do NOT induce vomiting. Call a physician immediately.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray jet, Foam, Extinguishing powder, Carbon dioxide (CO2), Sand. Co-ordinate fire-fighting measures to the fire surroundings.
Full water jet.
Firefighter Protection
Use suitable breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Avoid contact with skin, eyes and clothes.
Do not allow to enter into surface water or drains.
Take up mechanically.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
No hazardous reaction when handled and stored according to provisions. ( Health hazards : None ). Avoid contact with skin, eyes and clothes.
Keep/Store only in original container. Notice the directions for use on the label. Protect against direct sunlight. Keep away from heat.
Keep away from heat.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
See protective measures under point 7 and 8.
Tested protective gloves must be worn Breakthrough time (maximum wearing time) : 4 hours ( NBR (Nitrile rubber) , Thickness of the glove material : 0,4 mm ) . See information supplied by the manufacturer.
39 - Wear eye/face protection.
No special measures are necessary.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
No information available.
No information available.
No information available.
Stable under recommended storage and handling conditions (See section 7).
Oxidising agent, strong.
Carbon monoxide. Carbon dioxide. aldehydes. Ketone, Sulphur oxides, Nitrogen oxides (NOx). Thermal decomposition can lead to the escape of irritating gases and vapours.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Radolid Korrex EP 7010?
The signal word is no signal word.
What is the physical form of Radolid Korrex EP 7010?
Radolid Korrex EP 7010 is a paste appearing as paste . It has characteristic odor.
What is Radolid Korrex EP 7010 used for?
Lubricants, greases and release agents ( Fat ).
What is the melting point of Radolid Korrex EP 7010?
The melting point is ( 1013 hPa ) > 170 °C and the boiling point is ( 1013 hPa ) > 250 °C.