NextSDS Logo
Safety Data Sheet EN

Radolid Korrex EP 7010

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Radolid Korrex EP 7010

Regulatory Identifiers

CAS Number
N/A
REACH No.
not relevant (mixture)

Identified Uses

lubricants, greases, release products; observe technical data sheet; Product category: PC-TEC-11 Lubricants, greases, release agents

Uses advised against

Do not use for products which come into contact with foodstuffs. Do not use for private purposes (household).

Manufacturers & Suppliers

R

RADOLID Thiel GmbH

manufacturer

Langenstück 2, 58579 Schalksmühle

+49 2351 979494

Emergency Contacts

Emergency information service

+49 2351 979494

08:00 - 16:00

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified no signal word

Hazard Classifications

Not Classified

GHS Pictograms

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Polysulfides, di-tert-dodecyl EC: 270-335-7 68425-15-0 0.1 - 1% Yes
zinc naphthenate EC: 234-409-2 12001-85-3 0.1 - 1% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove casualty to fresh air and keep at rest. If breathing is irregular or stopped, immediately seek medical assistance and start first aid actions. In all cases of doubt, or when symptoms persist, seek medical advice.

Symptoms: Breathing difficulties.

Skin contact

Wash immediately with plenty of water and soap. Take off contaminated clothing. If skin irritation occurs: Get medical advice/attention.

Eye contact

Remove contact lenses, if present and easy to do. Continue rinsing. After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an ophthalmologist immediately. Protect uninjured eye.

Ingestion

Rinse mouth with water (only if the person is conscious). Do NOT induce vomiting. Observe aspiration hazard if vomiting occurs. Call a doctor if you feel unwell.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Fire extinguishing powder, Sand, Foam, Carbon dioxide (CO2)

Unsuitable media

Water jet, Water, Excess of water, Water spray

Specific hazards

In case of fire and/or explosion do not breathe fumes.

Instructions

Co-ordinate firefighting measures to the fire surroundings. Fight fire with normal precautions from a reasonable distance. Move undamaged containers from immediate hazard area if it can be done safely.

Firefighter Protection

Use water spray jet to protect personnel and to cool endangered containers.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Remove persons to safety. Avoid contact with eyes and skin. Use personal protective equipment as required. Eliminate all ignition sources if safe to do so. Provide fresh air.

Environmental

Make sure spills can be contained, e.g. in sump pallets or kerbed areas. Keep away from drains, surface and ground water. Retain contaminated washing water and dispose of it. Do not allow to enter into soil/subsoil.

Cleanup methods

Wipe up with absorbent material (e.g. cloth, fleece). Collect spillage: sawdust, kieselgur (diatomite), sand, universal binder

Materials: cloth, fleece, sawdust, kieselgur (diatomite), sand, universal binder

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with skin, eyes and clothes. Do not breathe vapour/aerosol. Provide fresh air. In case of inadequate ventilation wear respiratory protection.

Storage

No hazardous reaction when handled and stored according to provisions.

Hygiene

Wash hands after use. Do not eat, drink and smoke in work areas. Remove contaminated clothing and protective equipment before entering eating areas. Never keep food or drink in the vicinity of chemicals. Never place chemicals in containers that are normally used for food or drink. Keep away from food, drink and animal feedingstuffs.

Fire prevention

No special fire protection measures are necessary.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

Engineering

General ventilation.

Hands

Wear suitable gloves. Chemical protection gloves are suitable, which are tested according to EN 374. Permeation time (maximum wear time). 4 h. NBR: acrylonitrile-butadiene rubber. Thickness of the glove material. 0,12 mm. See information supplied by the manufacturer. For special purposes, it is recommended to check the resistance to chemicals of the protective gloves mentioned above together with the supplier of these gloves. In the case of wanting to use the gloves again, clean them before taking off and air them well. Unsuitable material.: Butyl caoutchouc (butyl rubber). NR (natural rubber, natural latex). CR (polychloroprene, chloroprene rubber).

Eyes

Wear eye/face protection.

Respiratory

Usually no personal respirative protection necessary. In case of inadequate ventilation wear respiratory protection.

Skin/Body

Preventive skin protection (barrier creams/ointments) is recommended.

Environmental

Use appropriate container to avoid environmental contamination. Keep away from drains, surface and ground water.

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Metal Corrosion
---
Appearance
---
Decomposition Temperature
not relevant
Freezing Point
---
Boiling Point
>250 °C
Colour Intensity
---
Solidification Point
---
Physical State Data
liquid
Properties Status
---
Flash Point
>200 °C
Vapor Density
---
Ph
not determined
Auto Ignition Temperature
not determined
Molecular Weight
---
Relative Evaporation Rate
---
State Under Standard Conditions
---
Softening Point
---
Odor
characteristic
Density
ca. 0.93 g/cm³ at 25 °C
Vapor Pressure
not determined
Cloud Point
---
Kinematic Viscosity
not determined
Upper Explosive Limit
not determined
Evaporation Rate
---
Solubility In Fat
---
Voc Content
---
Melting Point
>149 °C
Form
---
Solubility In Water
---
Flammability
this material is combustible, but will not ignite readily
Partition Coefficient
this information is not available
Explosive Limits
---
Solubility
not determined
Colour
light brown
Crystallisation Point
---
Physical State
liquid (paste)
Relative Density
---
Dynamic Viscosity
---
Odor Threshold
---
Lower Explosive Limit
not determined
Bulk Density
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

The product is chemically stable under recommended conditions of storage, use and temperature.

Reactivity

This material is not reactive under normal ambient conditions.

Hazardous reactions

No known hazardous reactions.

Avoid

There are no specific conditions known which have to be avoided.

Incompatible

Acids, Oxidisers

Decomposition

Reasonably anticipated hazardous decomposition products produced as a result of use, storage, spill and heating are not known. Hazardous combustion products: see section 5.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Radolid Korrex EP 7010?

The signal word is no signal word.

What is the physical form of Radolid Korrex EP 7010?

Radolid Korrex EP 7010 is a liquid (paste) with light brown color. It has characteristic odor.

What is the solubility of Radolid Korrex EP 7010?

not determined

What is Radolid Korrex EP 7010 used for?

lubricants, greases, release products; observe technical data sheet; Product category: PC-TEC-11 Lubricants, greases, release agents

What is the melting point of Radolid Korrex EP 7010?

The melting point is >149 °C and the boiling point is >250 °C.