NextSDS Logo
Safety Data Sheet EN

Weldwood Original Contact Cement Vial

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Weldwood Original Contact Cement Vial
Product Code
070798001299

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Adhesive

Manufacturers & Suppliers

D

DAP Global Inc.

manufacturer

2400 Boston Street Suite 200, Baltimore, MD 21224-4723

888-327-8477

Emergency Contacts

Emergency Contact

1-800-535-5053

Emergency Contact

1-352-323-3500

Emergency Contact

1-800-222-1222

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 4
Eye Irrit. Cat. 2
Flam. Liq. Cat. 2
Muta. Cat. 1B
Skin Irrit. Cat. 2
Skin Sens. Cat. 1
STOT SE Cat. 3

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H225 Highly flammable liquid and vapour.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H336 May cause drowsiness or dizziness.
H340 May cause genetic defects.

Precautionary Statements

P201 Obtain special instructions before use.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/../ equipment.
P242 Use only non-sparking tools.
P243 Take precautionary measures against static discharge.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P304 + P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical advice/attention.
P312 Call a POISON CENTER or doctor/physician if you feel unwell.
P321 Specific treatment (see ... on this label).
P332 + P313 If skin irritation occurs: Get medical advice/attention.
P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
P337 + P313 If eye irritation persists: Get medical advice/attention.
P362 Take off contaminated clothing.
P363 Wash contaminated clothing before reuse.
P370 + P378 In case of fire: Use... to extinguish.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
P501 Dispose of contents/container.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Ethyl acetate 141-78-6 10 - 30% Yes
Methyl ethyl ketone (MEK) 78-93-3 10 - 30% Yes
VM & P Naphtha 8032-32-4 10 - 30% Yes
Acetone 67-64-1 10 - 30% Yes
Phenol-formaldehyde Resin, Novolac 9003-35-4 7 - 13% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention immediately. NOTE: Only trained personnel should administer artificial respiration or give oxygen.

Skin contact

Wash skin with soap and water for 15 minutes. Get medical aid if symptoms persist. Remove and wash contaminated clothing. The use of vegetable oil or mineral oil is recommended for removal of this material from the skin. Flush exposed area with water while removing contaminated clothing. To remove from skin, remove completely with a dry cloth or paper towel, before washing with detergent and water.

Symptoms: irritation

Eye contact

If material gets into eyes, flush with water immediately for 15 minutes. Consult a physician.

Ingestion

If swallowed, DO NOT INDUCE VOMITING. Get medical attention immediately.

Immediate Medical Attention

Get medical attention immediately for inhalation and ingestion. Get medical aid if symptoms persist for skin contact. Consult a physician for eye contact.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Alcohol Foam, Carbon Dioxide, Dry Chemical, Foam, Water Spray or Fog, Water

Specific hazards

Vapors can form an ignitable mixture with air. Vapors can flow along surfaces to a distant ignition source and flash back. Vapors may form explosive mixtures with air. Containers may explode if exposed to extreme heat. Empty containers retain product residue (liquid and/or vapor). Vapor can ignite potentially causing an explosion.

Instructions

Use water spray to cool exposed surfaces. Cool fire-exposed containers using water spray.

Firefighter Protection

Wear self-contained breathing apparatus pressure-demand (NIOSH approved or equivalent) and full protective gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Review fire hazards before proceeding with clean up. Immediately eliminate sources of ignition. Keep people away from and upwind of spill/leak. Contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Read all product instructions before using. Scrape up dried material and place into containers.

Environmental

Prevent product from entering drains.

Cleanup methods

Soak up with inert absorbent material and dispose of as hazardous waste. Scrape up dried material and place into containers.

Materials: inert absorbent material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

KEEP OUT OF REACH OF CHILDREN! DO NOT TAKE INTERNALLY. Remove all sources of ignition. Keep away from open flames, hot surfaces and sources of ignition. Wear appropriate personal protection. Avoid breathing vapor and contact with eyes, skin and clothing. Wash thoroughly after handling. Do not use in areas where static sparks may be generated. Intentional misuse by deliberately concentrating and inhaling vapors may be harmful or fatal.

Storage

Store away from sources of ignition and heat. Store containers away from excessive heat and freezing. Store away from caustics and oxidizers. Keep containers tightly closed.

Hygiene

Wash thoroughly after handling.

Fire prevention

Remove all sources of ignition. Keep away from open flames, hot surfaces and sources of ignition. Avoid heat, sparks and open flames. Do not use in areas where static sparks may be generated.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Physical State
Thick Liquid
Physical State Data
liquid
State Under Standard Conditions
---
Appearance
Clear
Colour
---
Colour Intensity
---
Form
---
Odor
Not Established
Odor Threshold
Not Established
Ph
Not Applicable
Melting Point
---
Boiling Point
80 - 80 °C
Flash Point
Seta Closed Cup: -10 °C
Freezing Point
Not Established
Softening Point
---
Solidification Point
---
Cloud Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Evaporation Rate
Not Established
Vapor Pressure
Not Established
Vapor Density
Not Established
Relative Density
---
Bulk Density
---
Density
0.95 - 0.95 g/cm3
Flammability
Flammable Liquid
Upper Explosive Limit
N.E.
Lower Explosive Limit
N.E.
Explosive Limits
---
Auto Ignition Temperature
Not Established
Decomposition Temperature
Not Established
Solubility
---
Partition Coefficient
Not Established
Solubility In Water
Not Established
Solubility In Fat
---
Molecular Weight
---
Voc Content
---
Metal Corrosion
---
Dynamic Viscosity
Not Established
Kinematic Viscosity
---
Properties Status
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under recommended storage conditions.

Hazardous reactions

Exothermic reaction with strong acids. Strong oxidizers, alkali metals and alkaline earth metals may cause fires or explosions.

Avoid

Keep away from open flames, hot surfaces and sources of ignition. Keep away from oxidizing agents, strongly alkaline and strongly acid materials in order to avoid exothermic reactions. Avoid contact with skin, eyes and clothing. Do not smoke.

Incompatible

Open flames, hot surfaces and sources of ignition. Strong oxidizing agents, heat, strong acids, alkali metals and alkaline earth metals.

Decomposition

Normal decomposition products, i.e., COx, NOx.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1133
Shipping Name
Adhesives, containing a flammable liquid
Transport Class
3 Flammable liquid
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Weldwood Original Contact Cement Vial?

The signal word is danger.

What is the physical form of Weldwood Original Contact Cement Vial?

Weldwood Original Contact Cement Vial is a thick liquid appearing as clear . It has not established odor.

What is Weldwood Original Contact Cement Vial used for?

Adhesive

What are the hazard statements for Weldwood Original Contact Cement Vial?

This substance has 7 hazard statements:

  • H225: Highly flammable liquid and vapour.
  • H315: Causes skin irritation.
  • H317: May cause an allergic skin reaction.
  • H319: Causes serious eye irritation.
  • H332: Harmful if inhaled.
  • H336: May cause drowsiness or dizziness.
  • H340: May cause genetic defects.