NextSDS Logo
Safety Data Sheet EN

Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors
Product Code
7999101

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Caulking Compound

Manufacturers & Suppliers

D

DAP Global Inc.

manufacturer

2400 Boston Street Suite 200 Baltimore, MD 21224-4723

888-327-8477

Emergency Contacts

Medical/Poison Control

1-800-222-1222

Transportation/National Response Center

1-800-535-5053

Transportation/National Response Center

1-352-323-3500

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified warning

Hazard Classifications

Flam. Liq. Cat. 3
Skin Irrit. Cat. 2
Skin Sens. Cat. 1

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H226 Flammable liquid and vapour.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.

Precautionary Statements

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/../ equipment.
P242 Use only non-sparking tools.
P243 Take precautionary measures against static discharge.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P321 Specific treatment (see ... on this label).
P332 + P313 If skin irritation occurs: Get medical advice/attention.
P333 + P313 If skin irritation or rash occurs: Get medical advice/attention.
P362 Take off contaminated clothing.
P363 Wash contaminated clothing before reuse.
P370 + P378 In case of fire: Use... to extinguish.
P403 + P235 Store in a well-ventilated place. Keep cool.
P501 Dispose of contents/container.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
1-Chloro-4-(trifluoromethyl)-benzene 98-56-6 10 - 30% Yes
Limestone 1317-65-3 10 - 30% No
Hydrogenated petroleum resin 69430-35-9 7 - 13% No
Hydrotreated kerosene 64742-47-8 5 - 10% Yes
Styrene-alphamethylstyrene 9011-11-4 5 - 10% No
S-i-s block copolymer 25038-32-8 1 - 5% No
Xylenes 1330-20-7 1 - 5% Yes
White mineral oil 8042-47-5 1 - 5% Yes
Hydrogenated styrene isoprene block copolymer --- 1 - 5% No
Ethyl benezene 100-41-4 0.1 - 1% Yes

The text for GHS Hazard Statements shown above (if any) is given in the "Other information" Section.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, remove to fresh air. If breathing is difficult, leave the area to obtain fresh air. If continued breathing difficulty is experienced, get medical attention immediately. NOTE: Only trained personnel should administer artificial respiration or give oxygen.

Skin contact

Wash skin with soap and water for 15 minutes. Get medical aid if symptoms persist. Remove and wash contaminated clothing.

Eye contact

If material gets into eyes, flush with water immediately for 15 minutes. Consult a physician.

Ingestion

If swallowed, DO NOT INDUCE VOMITING. Get medical attention immediately.

Immediate Medical Attention

Get medical attention immediately (inhalation, ingestion); Consult a physician (eye contact); Get medical aid if symptoms persist (skin contact).

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Alcohol Foam, Carbon Dioxide, Dry Chemical, Foam, Water Spray or Fog, Water

Specific hazards

Vapors can form an ignitable mixture with air. Vapors can flow along surfaces to a distant ignition source and flash back. Vapors may form explosive mixtures with air. Containers may explode if exposed to extreme heat. Empty containers retain product residue (liquid and/or vapor). Vapor can ignite potentially causing an explosion.

Instructions

Use water spray to cool exposed surfaces.

Firefighter Protection

Wear self-contained breathing apparatus pressure-demand (NIOSH approved or equivalent) and full protective gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Review fire hazards before proceeding with clean up. Immediately eliminate sources of ignition. Keep people away from and upwind of spill/leak. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Read all product instructions before using. Scrape up dried material and place into containers.

Environmental

Prevent product from entering drains.

Cleanup methods

Soak up with inert absorbent material, Scrape up dried material and place into containers

Materials: inert absorbent material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

KEEP OUT OF REACH OF CHILDREN! DO NOT TAKE INTERNALLY. Remove all sources of ignition. Keep away from open flames, hot surfaces and sources of ignition. Wear appropriate personal protection. Avoid breathing vapor and contact with eyes, skin and clothing. Wash thoroughly after handling. Do not use in areas where static sparks may be generated.

Storage

Store away from sources of ignition and heat. Do not store at temperatures above 120 °F (49 °C). Store containers away from excessive heat and freezing. Store away from caustics and oxidizers. Keep containers tightly closed.

Hygiene

Wash thoroughly after handling.

Fire prevention

Remove all sources of ignition. Keep away from open flames, hot surfaces and sources of ignition. Avoid heat, sparks and open flames. Do not use in areas where static sparks may be generated.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Upper Explosive Limit
N.E.
Colour Intensity
---
Solubility
---
Relative Density
---
Solidification Point
---
Density
1.20 - 1.21 g/cm3
Metal Corrosion
---
Decomposition Temperature
Not Established
Colour
---
Bulk Density
---
Melting Point
---
Partition Coefficient
Not Established
Solubility In Water
Not Established
Lower Explosive Limit
N.E.
Solubility In Fat
---
Dynamic Viscosity
Not Established
Molecular Weight
---
Kinematic Viscosity
---
Flash Point
36.7 °C (Pensky-Martens Closed Cup)
Softening Point
---
Cloud Point
---
Vapor Density
Heavier Than Air
Crystallisation Point
---
Appearance
Colored
Odor Threshold
Not Established
Physical State Data
liquid
State Under Standard Conditions
---
Relative Evaporation Rate
---
Explosive Limits
---
Physical State
Paste
Form
---
Properties Status
---
Freezing Point
Not Established
Boiling Point
100 - 100 °C
Auto Ignition Temperature
Not Established
Flammability
Flammable Liquid Class IC
Voc Content
---
Ph
Not Applicable
Evaporation Rate
Not Established
Vapor Pressure
Not Established
Odor
Strong Solvent
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions.

Avoid

Keep away from open flames, hot surfaces and sources of ignition. Keep away from oxidizing agents, strongly alkaline and strongly acid materials in order to avoid exothermic reactions. Do not smoke.

Incompatible

Open flames, hot surfaces and sources of ignition. Keep away from strong oxidizing agents, heat and open flames. Strong acids and strong bases.

Decomposition

Normal decomposition products, i.e., COx, NOx.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1133
Shipping Name
Adhesives, containing a flammable liquid
Transport Class
3
Packing Group
III
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors?

The signal word is warning.

What is the physical form of Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors?

Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors is a paste appearing as colored . It has strong solvent odor.

What is Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors used for?

Caulking Compound

What are the hazard statements for Dynaflex 920 Premium Exterior Elastomeric Sealant - Colors?

This substance has 3 hazard statements:

  • H226: Flammable liquid and vapour.
  • H315: Causes skin irritation.
  • H317: May cause an allergic skin reaction.