NextSDS Logo
Safety Data Sheet EN

BONDERITE M-CR 600 AERO CHROMATE COATING

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-CR 600 AERO CHROMATE COATING
Product Code
3111505

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Chromating Products for Metals

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelina.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

OXIDIZING SOLID Cat. 2
Acute Tox. Cat. 3
Acute Tox. Cat. 2
Acute Tox. Cat. 2
Skin Corr. Cat. 1
Eye Dam. Cat. 1
Resp. Sens. Cat. 1
Skin Sens. Cat. 1
Muta. Cat. 1B
Carc. Cat. 1A
Repr. Cat. 1B
STOT SE Cat. 3
STOT RE Cat. 1

GHS Pictograms

GHS03 - Oxidizing

GHS03

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

GHS07 - Health hazard

GHS07

GHS08 - Serious health hazard

GHS08

Hazard Statements

H272 MAY INTENSIFY FIRE; OXIDIZER.
H301 TOXIC IF SWALLOWED.
H310 + H330 FATAL IN CONTACT WITH SKIN OR IF INHALED.
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H317 MAY CAUSE AN ALLERGIC SKIN REACTION.
H334 MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
H335 MAY CAUSE RESPIRATORY IRRITATION.
H340 MAY CAUSE GENETIC DEFECTS.
H350 MAY CAUSE CANCER.
H360 MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
H372 CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

Precautionary Statements

P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P220 Keep away from clothing and other combustible materials.
P260 Do not breathe dust.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P280 Wear protective gloves, clothing, eye and face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P301 + P330 + P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303 + P361 + P353 If on skin (or hair): Take off immediately all contaminated clothing.
P304 + P340 + P310 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or physician.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical attention.
P333 + P313 If skin irritation or rash occurs: Get medical attention.
P342 + P311 If experiencing respiratory symptoms: Call a poison center or physician.
P361 + P364 Take off immediately all contaminated clothing and wash it before reuse.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 + P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Rinse mouth.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture

Hazardous Component(s) | CAS Number | Weight %*

Chemical Name CAS Number Concentration Hazardous
Sodium borofluoride 13755-29-8 30 - 60% Yes
Chromium trioxide 1333-82-0 30 - 60% Yes
Dipotassium hexafluorozirconate 16923-95-8 10 - 30% Yes
04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If inhaled, immediately remove the affected person to fresh air. If symptoms develop and persist, get medical attention. Administer oxygen or artificial respiration as needed. Do not use mouth-to-mouth method if victim ingested or inhaled the substance.

Symptoms: Delayed effects possible after inhalation.

Skin contact

Remove contaminated clothing and footwear. Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Topical 10 % EDTA ointment can be used to treat chromate scabs and skin ulcers. A 10 % ascorbic acid solution may speed healing if applied promptly. Larger exposures may need additional treatment. Launder contaminated clothing before reuse. Discard any shoes or clothing items that cannot be decontaminated. In case of adverse health effects seek medical advice.

Symptoms: chromate scabs and skin ulcers

Eye contact

Immediately flush affected eye with large amounts of gently flowing water or 0.9% sterile saline solution for at least 15 minutes. Hold eyelid wide open. Get immediate medical attention. Eye flushing should continue during transportation to a doctor.

Ingestion

Get immediate medical attention. Do not induce vomiting. If individual is conscious, wash out mouth with water. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Get immediate medical attention.

Medical Treatment

Ocular exposure to corrosive fluoride compounds has been treated with isotonic sodium chloride or magnesium chloride. Dermal exposure to corrosive fluoride compounds has been treated with calcium gluconate or calcium carbonate gel applied topically to the affected areas to relieve pain at the site of exposure. Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use media appropriate for surrounding material. Water spray (fog), foam, dry chemical or carbon dioxide.

Unsuitable media

Not available.

Specific hazards

This product is an oxidizing agent and is a serious fire and explosion risk. Do not permit contact with combustible, organic, or other oxidizable materials. May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear self contained breathing apparatus. Wear protective equipment.

Firefighter Protection

Wear self contained breathing apparatus. Wear protective equipment.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so.

Cleanup methods

Scrape up spilled material and place in a closed container for disposal.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing dust. Use only with adequate ventilation. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material. Do not take internally. For industrial use only.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials.

Hygiene

Wash thoroughly after handling. Launder work clothes frequently. Do not store or consume food, drink, or tobacco products in areas where they may become contaminated with this material.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Melting Point
> 180 °C (> 356°F)
Solubility
Soluble Water
Voc Content
---
Solubility In Fat
---
Dynamic Viscosity
Not available.
Molecular Weight
---
State Under Standard Conditions
---
Softening Point
---
Crystallisation Point
---
Relative Evaporation Rate
---
Flammability
The product is not flammable.
Vapor Pressure
< 0.1 hPa (20 °C (68°F))
Evaporation Rate
---
Flash Point
> 260 °C (> 500°F)
Metal Corrosion
---
Auto Ignition Temperature
Not available.
Partition Coefficient
Not available.
Ph
1.3 - 1.7
Physical State Data
solid
Odor Threshold
Not available.
Upper Explosive Limit
Not available.
Properties Status
---
Solidification Point
---
Odor
Odourless / Odorless
Relative Density
---
Form
---
Bulk Density
---
Density
---
Kinematic Viscosity
Not available.
Colour
Light brown
Explosive Limits
---
Cloud Point
---
Vapor Density
---
Appearance
---
Physical State
Solid
Boiling Point
Not applicable, Decomposition.
Colour Intensity
---
Decomposition Temperature
Not available.
Freezing Point
---
Lower Explosive Limit
Not available.
Solubility In Water
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under recommended storage conditions.

Reactivity

Not available.

Hazardous reactions

Will not occur.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

This product may react with strong reducing agents. Keep away from organic and combustible materials. Strong bases. Metals.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Hydrogen fluoride. Oxides of boron. Chromium oxide.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1463
Shipping Name
Chromium trioxide, anhydrous
Transport Class
5.1 (6.1, 8)
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for BONDERITE M-CR 600 AERO CHROMATE COATING?

The signal word is danger.

What is the physical form of BONDERITE M-CR 600 AERO CHROMATE COATING?

BONDERITE M-CR 600 AERO CHROMATE COATING is a solid with light brown color. It has odourless / odorless odor.

What is the solubility of BONDERITE M-CR 600 AERO CHROMATE COATING?

Soluble Water

What is BONDERITE M-CR 600 AERO CHROMATE COATING used for?

Chromating Products for Metals

What are the hazard statements for BONDERITE M-CR 600 AERO CHROMATE COATING?

This substance has 11 hazard statements:

  • H272: MAY INTENSIFY FIRE; OXIDIZER.
  • H301: TOXIC IF SWALLOWED.
  • H310 + H330: FATAL IN CONTACT WITH SKIN OR IF INHALED.
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H317: MAY CAUSE AN ALLERGIC SKIN REACTION.
  • H334: MAY CAUSE ALLERGY OR ASTHMA SYMPTOMS OR BREATHING DIFFICULTIES IF INHALED.
  • H335: MAY CAUSE RESPIRATORY IRRITATION.
  • H340: MAY CAUSE GENETIC DEFECTS.
  • H350: MAY CAUSE CANCER.
  • H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD.
  • H372: CAUSES DAMAGE TO ORGANS THROUGH PROLONGED OR REPEATED EXPOSURE.

What is the melting point of BONDERITE M-CR 600 AERO CHROMATE COATING?

The melting point is > 180 °C (> 356°F) and the boiling point is Not applicable, Decomposition..