NextSDS Logo
Safety Data Sheet EN

BONDERITE M-CR 47S CHROMATE COATING

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
BONDERITE M-CR 47S CHROMATE COATING
Product Code
593839
Synonyms
ALODINE 47S

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Cleaner

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Acute Tox. Cat. 2
Acute Tox. Cat. 3
Acute Tox. Cat. 1
Skin Corr. Cat. 1B
Eye Dam. Cat. 1

GHS Pictograms

GHS05 - Corrosive

GHS05

GHS06 - Acute toxicity

GHS06

Hazard Statements

H300 + H310 FATAL IF SWALLOWED OR IN CONTACT WITH SKIN.
H314 MAY CAUSE DELAYED BURNS (NOT IMMEDIATELY PAINFUL OR VISIBLE)!
H314 CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
H331 TOXIC IF INHALED.
H372 LONG TERM EXPOSURE TO FLUORIDES OVER YEARS MAY CAUSE FLUOROSIS!
CONTAINS FLUORIDES.

Precautionary Statements

P233 Keep container tightly closed.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash affected area thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves, clothing, eye and face protection.
P301 + P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/ physician.
P302 + P350 IF ON SKIN: Gently wash with plenty of soap and water.
P304 + P341 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P310 Immediately call a POISON CENTER or physician.
P330 Rinse mouth.
P331 Do NOT induce vomiting.
P338 Remove contact lenses, if present and easy to do. Continue rinsing.
P351 IF IN EYES: Rinse cautiously with water for several minutes.
P361 If on skin (or hair): Take off immediately all contaminated clothing.
P362 Take off contaminated clothing.
P403 Store in a well-ventilated place.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.
Avoid breathing vapors, mist, or spray.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Type mixture
Chemical Name CAS Number Concentration Hazardous
Hydrogen fluoride 7664-39-3 10 - 30% Yes

Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist. If breathing is difficult, give oxygen. Trained personnel should administer 2.5% calcium gluconate through a nebulizer for 20 minutes.

Skin contact

Remove contaminated clothing and footwear while rinsing the affected area with large amounts of running water for at least 15 minutes. GET IMMEDIATE MEDICAL ATTENTION. If iced solution of 0.13% aqueous Benzalkonium Chloride (Zephiran) or 2.5% calcium gluconate gel is available, rinsing may be limited to 5 minutes, with the soak solution or gel applied as soon as the rinsing is stopped. If using calcium gluconate gel, it should be continuously re-applied and massaged into the affected area until pain has been relieved for at least 30 minutes. If Benzalkonium Chloride (Zephiran) or calcium gluconate gel is not available, rinsing must continue until medical treatment is provided.

Eye contact

Rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention.

Ingestion

Get immediate medical attention. Do not induce vomiting. Attempt immediate administration of a fluoride binding substance: milk, chewable calcium carbonate tablets or 4-8 ounces (120-240 ml) of milk of magnesia or a liquid antacid. Avoid large amounts of liquid as it may induce vomiting. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

GET IMMEDIATE MEDICAL ATTENTION.

Medical Treatment

Treatment of hypocalcemia associated with corrosive fluoride compounds exposure may be corrected by intravenous calcium gluconate or calcium chloride. Treatment of hypomagnesemia may be corrected by intravenous magnesium sulfate.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.

Instructions

Wear full protective clothing. Wear self-contained breathing apparatus.

Firefighter Protection

Wear full protective clothing. Wear self-contained breathing apparatus.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways.

Cleanup methods

Absorb spill with inert material. Shovel material into appropriate container for disposal.

Materials: inert material

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Avoid breathing vapors or mists of this product. For industrial use only. Do not take internally.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials.

Hygiene

Wash thoroughly after handling.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Partition Coefficient
Not determined
Properties Status
---
Relative Density
1.05 - 1.10 at 15.56 °C (60.01 °F)
Odor Threshold
Not available.
Odor
Sharp
State Under Standard Conditions
---
Boiling Point
> 100 °C (> 212°F)
Solubility In Water
Complete
Flammability
Not applicable
Appearance
---
Decomposition Temperature
Not available.
Form
---
Solubility
---
Molecular Weight
---
Kinematic Viscosity
Not available.
Explosive Limits
---
Physical State
Liquid
Solubility In Fat
---
Freezing Point
---
Cloud Point
---
Flash Point
Not applicable
Evaporation Rate
Not available.
Solidification Point
---
Bulk Density
---
Relative Evaporation Rate
---
Vapor Density
Not determined
Physical State Data
liquid
Voc Content
Not applicable
Lower Explosive Limit
Not available.
Density
---
Softening Point
---
Upper Explosive Limit
Not available.
Colour Intensity
---
Dynamic Viscosity
---
Crystallisation Point
---
Melting Point
Not determined
Vapor Pressure
Not determined
Ph
< 1.0
Colour
Red
Auto Ignition Temperature
Not applicable
Metal Corrosion
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

Not available.

Hazardous reactions

Will not occur.

Avoid

Keep away from heat, ignition sources and incompatible materials.

Incompatible

This product may react with strong acids, bases and oxidizing agents. This material will react with glass, concrete, certain metals, silica containing materials, rubber, leather, and many organics.

Decomposition

Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. May liberate hydrogen fluoride.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
UN1790
Shipping Name
Hydrofluoric acid solution
Transport Class
8 (6.1)
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What other names is BONDERITE M-CR 47S CHROMATE COATING known by?

BONDERITE M-CR 47S CHROMATE COATING is also known as: ALODINE 47S

What is the hazard signal word for BONDERITE M-CR 47S CHROMATE COATING?

The signal word is danger.

What is the physical form of BONDERITE M-CR 47S CHROMATE COATING?

BONDERITE M-CR 47S CHROMATE COATING is a liquid with red color. It has sharp odor.

What is BONDERITE M-CR 47S CHROMATE COATING used for?

Cleaner

What are the hazard statements for BONDERITE M-CR 47S CHROMATE COATING?

This substance has 6 hazard statements:

  • H300 + H310: FATAL IF SWALLOWED OR IN CONTACT WITH SKIN.
  • H314: MAY CAUSE DELAYED BURNS (NOT IMMEDIATELY PAINFUL OR VISIBLE)!
  • H314: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE.
  • H331: TOXIC IF INHALED.
  • H372: LONG TERM EXPOSURE TO FLUORIDES OVER YEARS MAY CAUSE FLUOROSIS!
  • CONTAINS FLUORIDES.

What is the melting point of BONDERITE M-CR 47S CHROMATE COATING?

The melting point is Not determined and the boiling point is > 100 °C (> 212°F).