Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER
- Product Code
- 893784
Regulatory Identifiers
- CAS Number
- N/A
Identified Uses
Sealant
Uses advised against
None identified
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| lithium acetate | 546-89-4 | 10 - 30% | Yes |
| Benzene, 1,1'-oxybis-, tetrapropylene derivs., sulfonated, sodium salts | 119345-04-9 | 1 - 5% | Yes |
Notes
* Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.
First Aid Measures
Emergency procedures for chemical exposure incidents
Remove person immediately to fresh air. Seek medical attention if symptoms develop or persist.
Flush with large amounts of water. If irritation persists, repeat flushing and get medical attention. Discard any shoes or clothing items that cannot be decontaminated.
Rinse immediately with plenty of water and seek medical advice.
Get medical attention. DO NOT induce vomiting unless directed to do so by medical personnel.
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Water spray (fog), foam, dry chemical or carbon dioxide.
Not available.
May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses.
Firefighter Protection
Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Materials: inert material
Related Products
Similar products with comparable safety profiles
BONDERITE M-NT 601
---
BONDERITE M-NT 1820 R2
---
BONDERITE M-ED ALUMINUX LL ANODIZING
---
BONDERITE M-NT 802 N known as Alodine 802 N
---
BONDERITE M-NT 3200 REP BU
---
BONDERITE M-NT 4595 CONV C known as ALODINE 4595
---
BONDERITE M-ED EA1022 ANODIZING ADDITIVE
---
BONDERITE M-NT 770X R N CONVERSION COATING
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid skin and eye contact. Wash thoroughly after handling. Provide adequate ventilation. Avoid breathing vapors or mists of this product. Do not take internally.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Thaw and mix thoroughly if frozen.
Wash thoroughly after handling.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Provide local and general exhaust ventilation to effectively remove and prevent buildup of any vapors or mists generated from the handling of this product.
Chemical resistant, impermeable gloves. Gloves should be tested to determine suitability for prolonged contact.
Wear safety glasses; chemical goggles (if splashing is possible).
If ventilation is not sufficient to effectively prevent buildup of aerosols, mists or vapors, appropriate NIOSH/MSHA respiratory protection must be provided.
Chemical resistant, impermeable gloves.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Store away from incompatible materials.
This product may react with strong oxidizing agents.
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of sulfur.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER?
The signal word is danger.
What is the physical form of BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER?
BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER is a liquid with light yellow color. It has mild odor.
What is the solubility of BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER?
Complete Water
What is BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER used for?
Sealant
What are the hazard statements for BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER?
This substance has 2 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H318: CAUSES SERIOUS EYE DAMAGE.
What is the melting point of BONDERITE M-NT NF-1 R ANODIZING SEAL known as ALMECO SEAL NF-1 REPLENISH ER?
The melting point is Not applicable and the boiling point is 211 °F (99.4 °C).