Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- BONDERITE M-ED SEAL MT ADDITIVE
- Product Code
- 597688
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS05
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ammonium acetate | 631-61-8 | 10 - 30% | Yes |
| Surfactant(s) | --- | 10 - 30% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
If inhaled, immediately remove the affected person to fresh air. If symptoms develop and persist, get medical attention. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention.
Immediately flush eyes with water for at least 15 minutes, while holding eyelids open. Seek medical attention at once.
Get medical attention. DO NOT induce vomiting unless directed to do so by medical personnel.
Immediate Medical Attention
Seek medical attention at once (for eyes). Get medical attention if symptoms develop and persist (for inhalation, skin, ingestion).
Medical Treatment
Treat symptomatically and supportively.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Use media appropriate for surrounding material.
Not available.
This product is an aqueous mixture which will not burn.
Wear full protective clothing. Wear self-contained breathing apparatus.
Firefighter Protection
Wear full protective clothing. Wear self-contained breathing apparatus.
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Prevent further leakage or spillage if safe to do so.
Absorb spill with inert material. Shovel material into appropriate container for disposal.
Related Products
Similar products with comparable safety profiles
BONDERITE M-ED SEAL 1085
---
BONDERITE M-ED SEAL 2500
---
BONDERITE M-ED SEAL 2121 A
---
BONDERITE M-ED SEAL NF-1 ANODIZING SEAL known as ALMECO SEAL NF-1 ADDITIVE
---
BONDERITE M-ED SPEC S
---
BONDERITE M-ED SPEC RO
---
BONDERITE M-ED EA1022 ANODIZING ADDITIVE
---
BONDERITE M-ED EA1010
---
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Do not take internally. For industrial use only. Provide adequate ventilation.
Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Thaw and mix thoroughly if frozen.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Ventilation should effectively remove and prevent buildup of any vapor/mist/fume/dust generated from the handling of this product.
Wear impervious gloves for prolonged contact. Gloves should be tested to determine suitability for prolonged contact.
Safety goggles or safety glasses with side shields.
If ventilation is not sufficient to effectively prevent buildup of aerosols, mists or vapors, appropriate NIOSH/MSHA respiratory protection must be provided.
Use of impervious apron and boots are recommended.
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable at normal conditions.
Not available.
None under normal processing.
Keep away from heat, ignition sources and incompatible materials.
This product may react with strong acids, bases and oxidizing agents.
Upon decomposition, this product emits oxides of sulfur, carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- 3082
- Shipping Name
- RQ, Environmentally hazardous substance, liquid, n.o.s.
- Transport Class
- 9
- Packing Group
- III
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for BONDERITE M-ED SEAL MT ADDITIVE?
The signal word is danger.
What is the physical form of BONDERITE M-ED SEAL MT ADDITIVE?
BONDERITE M-ED SEAL MT ADDITIVE is a liquid with light amber color. It has vinegar odor.
What is the solubility of BONDERITE M-ED SEAL MT ADDITIVE?
Complete Water
What are the hazard statements for BONDERITE M-ED SEAL MT ADDITIVE?
This substance has 2 hazard statements:
- H315: CAUSES SKIN IRRITATION.
- H318: CAUSES SERIOUS EYE DAMAGE.
What is the melting point of BONDERITE M-ED SEAL MT ADDITIVE?
The melting point is Not determined and the boiling point is 220 °F (104.4 °C)calculated.