Identification
Product identifiers, regulatory numbers, and supplier information
Product Information
- Product Name
- Loctite Super Glue Ultra Control Gel
- Product Form
- Adhesive
- Product Code
- 1766537
Regulatory Identifiers
- CAS Number
- N/A
Manufacturers & Suppliers
Henkel Corporation
manufacturer
One Henkel Way, Rocky Hill, Connecticut 06067
+1 (860) 571-5100
http://www.henkelna.com
Emergency Contacts
Poison Control Center
1-877-671-4608
Poison Control Center
1-303-592-1711
CHEMTREC
1-800-424-9300
CHEMTREC
1-703-527-3887
Hazard Identification
GHS classification, signal word, pictograms, and hazard statements
Hazard Classifications
GHS Pictograms
GHS07
GHS08
Hazard Statements
Precautionary Statements
Get a free compliance audit
Upload your SDS inventory and get a detailed compliance report
Composition / Information on Ingredients
Chemical components, concentration ranges, and hazardous substance identification
| Chemical Name | CAS Number | Concentration | Hazardous |
|---|---|---|---|
| Ethyl 2-cyanoacrylate | 7085-85-0 | 80 - 100% | Yes |
| Siloxanes and Silicones, di-Me, reaction products with silica | 67762-90-7 | 1 - 5% | Yes |
| Bis(2-hydroxy-3-tert-butyl-5-methylphenyl)methane | 119-47-1 | 0.1 - 1% | Yes |
First Aid Measures
Emergency procedures for chemical exposure incidents
Move to fresh air. If symptoms persist, seek medical advice.
Do not pull bonded skin apart. Soak in warm soapy water. Gently peel apart using a blunt instrument. If lips are bonded, apply warm water to the lips and encourage wetting and pressure from saliva in mouth. Peel or roll lips apart.
Symptoms: If skin is burned due to the rapid generation of heat by a large drop.
Immediately flush with plenty of water for at least 15 minutes. Get medical attention. If eyelids are bonded closed, release eyelashes with warm water by covering with a wet pad. Keep eye covered until debonding is complete, usually within 1-3 days.
Symptoms: Cyanoacrylate will bond to eye protein and will cause a lachrymatory effect which will help to debond the adhesive.
Ensure breathing passages are not obstructed. Saliva will separate any solidified product in several hours. Prevent the patient from swallowing any separated mass.
Symptoms: The product will polymerize rapidly and bond to the mouth making it almost impossible to swallow.
Immediate Medical Attention
If skin is burned due to the rapid generation of heat by a large drop, seek medical attention. Medical attention should be sought in case solid particles of polymerized cyanoacrylate trapped behind the eyelid caused abrasive damage.
Medical Treatment
Surgery is not necessary to separate accidentally bonded tissues. Experience has shown that bonded tissues are best treated by passive, non-surgical first aid. If rapid curing has caused thermal burns they should be treated symptomatically after adhesive is removed.
Firefighting Measures
Extinguishing media, specific hazards, and firefighter protection
Carbon dioxide, foam, powder
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA).
Firefighter Protection
Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA).
Accidental Release Measures
Spill cleanup procedures, containment, and environmental protection
isolate the hazard area and deny entry to unnecessary and unprotected personnel.
Do not allow product to enter sewer or waterways.
Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor.
Related Products
Similar products with comparable safety profiles
Handling and Storage
Safe handling precautions, storage conditions, and workplace requirements
Avoid contact with eyes, skin and clothing. Avoid breathing vapors or mists of this product. Wash thoroughly after handling. Avoid contact with fabric or paper goods. Contact with these materials may cause rapid polymerization which can generate smoke and strong irritating vapors, and cause thermal burns.
Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use.
Wash thoroughly after handling.
Keep in a cool, well ventilated area away from heat, sparks and open flame.
Exposure Controls / PPE
Occupational exposure limits, engineering controls, and protective equipment
Physical and Chemical Properties
Appearance, physical state, melting point, boiling point, and material characteristics
Stability and Reactivity
Chemical stability, hazardous reactions, and incompatible materials
Stable under recommended storage conditions.
Not available.
Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and alcohols.
None if used for intended purpose.
Water, Amines, Alkalis, Alcohols.
Ecological Information
Environmental toxicity, biodegradation, and bioaccumulation data
The data for this section has not been processed yet.
Disposal Considerations
Waste treatment methods, disposal recommendations, and waste codes
The data for this section has not been processed yet.
Transport Information
UN numbers, shipping names, transport classes, and regulatory requirements
- UN Number
- UN3334
- Shipping Name
- Aviation regulated liquid, n.o.s. (Cyanoacrylate ester)
- Transport Class
- 9
- Packing Group
- III
Not more than 500 ml (each inner package) - Unrestricted
Regulatory Information
Chemical regulations, safety assessments, and compliance status
The data for this section has not been processed yet.
Frequently Asked Questions
Common questions about safety, handling, and properties
What is the hazard signal word for Loctite Super Glue Ultra Control Gel?
The signal word is danger.
What is the physical form of Loctite Super Glue Ultra Control Gel?
Loctite Super Glue Ultra Control Gel is a clear appearing as clear with colourless / colorless color. It has irritating odor.
What is the solubility of Loctite Super Glue Ultra Control Gel?
Polymerizes on contact with water. Water
What are the hazard statements for Loctite Super Glue Ultra Control Gel?
This substance has 5 hazard statements:
- H227: COMBUSTIBLE LIQUID
- H315: CAUSES SKIN IRRITATION
- H319: CAUSES SERIOUS EYE IRRITATION
- H335: MAY CAUSE RESPIRATORY IRRITATION
- H360: MAY DAMAGE FERTILITY OR THE UNBORN CHILD
What is the melting point of Loctite Super Glue Ultra Control Gel?
The melting point is Not applicable, Product is a liquid and the boiling point is > 100 °C (> 212°F).