NextSDS Logo
Safety Data Sheet EN

LOCTITE DURO-TAK UV VP 5008BP PA 16KG

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report.

Get Free Audit
01

Identification

Product identifiers, regulatory numbers, and supplier information

Product Information

Product Name
LOCTITE DURO-TAK UV VP 5008BP PA 16KG
Product Code
2953140

Regulatory Identifiers

CAS Number
N/A

Identified Uses

Pressure Sensitive Adhesives

Uses advised against

None identified

Manufacturers & Suppliers

Henkel Corporation logo

Henkel Corporation

manufacturer

One Henkel Way, Rocky Hill, Connecticut 06067

+1 (860) 571-5100

www.henkelna.com

Emergency Contacts

Poison Control Center

1-877-671-4608

Poison Control Center

1-303-592-1711

CHEMTREC

1-800-424-9300

CHEMTREC

1-703-527-3887

02

Hazard Identification

GHS classification, signal word, pictograms, and hazard statements

Classified danger

Hazard Classifications

Flam. Liq. Cat. 2
Skin Irrit. Cat. 2
Eye Irrit. Cat. 2A
STOT SE Cat. 3

GHS Pictograms

GHS02 - Flammable

GHS02

GHS07 - Health hazard

GHS07

Hazard Statements

H225 HIGHLY FLAMMABLE LIQUID AND VAPOUR.
H315 CAUSES SKIN IRRITATION.
H319 CAUSES SERIOUS EYE IRRITATION.
H336 MAY CAUSE DROWSINESS OR DIZZINESS.

Precautionary Statements

P210 Keep away from heat, sparks, open flames, hot surfaces - no smoking.
P233 Keep container tightly closed.
P233 Keep container tightly closed.
P235 Keep cool.
P241 Use explosion-proof equipment.
P242 Use non-sparking tools.
P243 Take action to prevent static discharges.
P261 Avoid breathing vapors, mist, or spray.
P264 Wash affected area thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P273 No release into water.
P280 Wear protective gloves, eye protection, and face protection.
P304 + P341 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P312 Call a POISON CENTER or physician if you feel unwell.
P332 + P313 If skin irritation occurs: Get medical attention.
P337 + P313 If eye irritation persists: Get medical attention.
P361 If on skin (or hair): Take off immediately all contaminated clothing.
P362 Take off contaminated clothing.
P370 + P378 In case of fire: Use foam, dry chemical or carbon dioxide to extinguish.
P403 Store in a well-ventilated place.
P403 Store in a well-ventilated place.
P405 Store locked up.
P501 Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.

Get a free compliance audit

Upload your SDS inventory and get a detailed compliance report

Free Audit
03

Composition / Information on Ingredients

Chemical components, concentration ranges, and hazardous substance identification

Notes

Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections.

04

First Aid Measures

Emergency procedures for chemical exposure incidents

Inhalation

If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Move to fresh air. If symptoms persist, seek medical advice.

Skin contact

Immediately flush skin with plenty of water (using soap, if available). Remove contaminated clothing and shoes. Get medical attention. Wash contaminated clothing before reuse. Thoroughly clean shoes before reuse. Discard any shoes or clothing items that cannot be decontaminated.

Eye contact

Check for and remove any contact lenses. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention.

Ingestion

If material is ingested, immediately contact a physician or poison control center. DO NOT induce vomiting unless directed to do so by medical personnel. If vomiting occurs, prevent aspiration by keeping the patient's head below the knees. Never give anything by mouth to an unconscious person.

Immediate Medical Attention

Get medical attention.

05

Firefighting Measures

Extinguishing media, specific hazards, and firefighter protection

Suitable media

Use extinguishing measures appropriate to local circumstances and the surrounding environment. Water spray (fog), foam, dry chemical or carbon dioxide.

Specific hazards

Vapors may accumulate in low or confined areas, travel considerable distance to source of ignition, and flash back. Closed containers may rupture (due to build up of pressure) when exposed to extreme heat.

Instructions

In case of fire, keep containers cool with water spray.

Firefighter Protection

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

06

Accidental Release Measures

Spill cleanup procedures, containment, and environmental protection

Emergency procedures

isolate the hazard area and deny entry to unnecessary and unprotected personnel.

Environmental

Prevent further leakage or spillage if safe to do so.

Cleanup methods

Transfer liquids to covered metal containers for recovery or disposal, or remove with inert absorbent.

Related Products

Similar products with comparable safety profiles

07

Handling and Storage

Safe handling precautions, storage conditions, and workplace requirements

Handling

Make sure containers are properly grounded before use or transfer of material. Keep container closed. Do not breathe gas/fumes/vapor/spray. Use only with adequate ventilation. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Do not taste or swallow. Do not handle or store near an open flame, heat or other sources of ignition. 'Empty' containers retain product residue (liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition; they may explode.

Storage

Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. Store in original container until ready to use.

Hygiene

Wash thoroughly after handling.

Fire prevention

Do not handle or store near an open flame, heat or other sources of ignition. Keep away from heat, spark and flame. Ground and bond metal containers for liquid transfer to avoid static sparks.

08

Exposure Controls / PPE

Occupational exposure limits, engineering controls, and protective equipment

09

Physical and Chemical Properties

Appearance, physical state, melting point, boiling point, and material characteristics

Flammability
Not applicable
Ph
Not applicable
Explosive Limits
---
Colour
Clear
Decomposition Temperature
Not available.
Odor
Acrylic
Relative Density
7.3 - 7.4
Dynamic Viscosity
---
Upper Explosive Limit
Not available.
Evaporation Rate
Not available.
Properties Status
---
Solubility
---
Softening Point
---
Freezing Point
---
Boiling Point
Not available.
Crystallisation Point
---
Metal Corrosion
---
Relative Evaporation Rate
---
Physical State Data
liquid
Form
---
State Under Standard Conditions
---
Density
---
Partition Coefficient
Not available.
Lower Explosive Limit
Not available.
Voc Content
35 - 40 %
Auto Ignition Temperature
Not available.
Bulk Density
---
Flash Point
-4 °C (24.8 °F)
Physical State
liquid
Solubility In Water
Insoluble
Vapor Density
---
Odor Threshold
Not available.
Melting Point
Not available.
Solidification Point
---
Molecular Weight
---
Kinematic Viscosity
---
Vapor Pressure
Not available.
Colour Intensity
---
Solubility In Fat
---
Appearance
---
Cloud Point
---
10

Stability and Reactivity

Chemical stability, hazardous reactions, and incompatible materials

Stability

Stable under normal conditions of storage and use.

Reactivity

This product may react with strong acids, bases and oxidizing agents.

Hazardous reactions

None under normal processing.

Avoid

Keep away from heat, ignition sources and incompatible materials. Take measures to prevent the build-up of electrostatic charges.

Incompatible

Strong acids, alkalies and oxidizing agents.

Decomposition

Irritating and toxic gases or fumes may be released during a fire. Oxides of carbon.

12

Ecological Information

Environmental toxicity, biodegradation, and bioaccumulation data

The data for this section has not been processed yet.

13

Disposal Considerations

Waste treatment methods, disposal recommendations, and waste codes

The data for this section has not been processed yet.

14

Transport Information

UN numbers, shipping names, transport classes, and regulatory requirements

UN Number
1133
Shipping Name
Adhesives
Transport Class
3
Packing Group
II
15

Regulatory Information

Chemical regulations, safety assessments, and compliance status

The data for this section has not been processed yet.

?

Frequently Asked Questions

Common questions about safety, handling, and properties

What is the hazard signal word for LOCTITE DURO-TAK UV VP 5008BP PA 16KG?

The signal word is danger.

What is the physical form of LOCTITE DURO-TAK UV VP 5008BP PA 16KG?

LOCTITE DURO-TAK UV VP 5008BP PA 16KG is a liquid with clear color. It has acrylic odor.

What is LOCTITE DURO-TAK UV VP 5008BP PA 16KG used for?

Pressure Sensitive Adhesives

What are the hazard statements for LOCTITE DURO-TAK UV VP 5008BP PA 16KG?

This substance has 4 hazard statements:

  • H225: HIGHLY FLAMMABLE LIQUID AND VAPOUR.
  • H315: CAUSES SKIN IRRITATION.
  • H319: CAUSES SERIOUS EYE IRRITATION.
  • H336: MAY CAUSE DROWSINESS OR DIZZINESS.

What is the melting point of LOCTITE DURO-TAK UV VP 5008BP PA 16KG?

The melting point is Not available. and the boiling point is Not available..